MAX713(2002) 데이터 시트보기 (PDF) - Maxim Integrated

부품명

상세내역

제조사

MAX713
(Rev.:2002)

NiCd/NiMH Battery Fast-Charge Controllers

Maxim Integrated 

NiCd/NiMH Battery

Fast-Charge Controllers

Getting Started

The MAX712/MAX713 are simple to use. A complete

linear-mode or switch-mode fast-charge circuit can be

designed in a few easy steps. A linear-mode design

uses the fewest components and supplies a load while

charging, while a switch-mode design may be neces-

sary if lower heat dissipation is desired.

1) Follow the battery manufacturer’s recommendations

on maximum charge currents and charge-termination

methods for the specific batteries in your application.

Table 1 provides general guidelines.

Table 1. Fast-Charge Termination Methods

Charge

Rate

> 2C

2C to C/2

NiMH Batteries

∆V/∆t and

temperature,

MAX712 or MAX713

∆V/∆t and/or

temperature,

MAX712 or MAX713

NiCd Batteries

∆V/∆t and/or

temperature, MAX713

∆V/∆t and/or

temperature, MAX713

< C/2

∆V/∆t and/or

temperature, MAX712

∆V/∆t and/or

temperature, MAX713

2) Decide on a charge rate (Tables 3 and 5). The slow-

est fast-charge rate for the MAX712/MAX713 is C/4,

because the maximum fast-charge timeout period is

264 minutes. A C/3 rate charges the battery in about

three hours. The current in mA required to charge at

this rate is calculated as follows:

IFAST = (capacity of battery in mAh)

–––––––––––––––––––––––––

(charge time in hours)

Depending on the battery, charging efficiency can be

as low as 80%, so a C/3 fast charge could take 3 hours

and 45 minutes. This reflects the efficiency with which

electrical energy is converted to chemical energy within

the battery, and is not the same as the power-

conversion efficiency of the MAX712/MAX713.

3) Decide on the number of cells to be charged (Table 2).

If your battery stack exceeds 11 cells, see the Linear-

Mode High Series Cell Count section. Whenever

changing the number of cells to be charged, PGM0

and PGM1 must be adjusted accordingly. Attempting

to charge more or fewer cells than the number pro-

grammed can disable the voltage-slope fast-charge

termination circuitry. The internal ADC’s input volt-

age range is limited to between 1.4V and 1.9V (see

the Electrical Characteristics), and is equal to the

voltage across the battery divided by the number of

cells programmed (using PGM0 and PGM1, as in

Table 2). When the ADC’s input voltage falls out of

its specified range, the voltage-slope termination cir-

cuitry can be disabled.

4) Choose an external DC power source (e.g., wall

cube). Its minimum output voltage (including ripple)

must be greater than 6V and at least 1.5V higher (2V

for switch mode) than the maximum battery voltage

while charging. This specification is critical because

normal fast-charge termination is ensured only if this

requirement is maintained (see Powering the

MAX712/MAX713 section for more details).

5) For linear-mode designs, calculate the worst-case

power dissipation of the power PNP and diode (Q1

and D1 in the Typical Operating Circuit) in watts,

using the following formula:

PDPNP = (maximum wall-cube voltage under

load - minimum battery voltage) x (charge current

in amps)

If the maximum power dissipation is not tolerable for

your application, refer to the Detailed Description or

use a switch-mode design (see Switch-Mode

Operation in the Applications Information section,

and see the MAX713 EV kit manual).

6) For both linear and switch-mode designs, limit cur-

rent into V+ to between 5mA and 20mA. For a fixed

or narrow-range input voltage, choose R1 in the

Typical Operation Circuit using the following formula:

R1 = (minimum wall-cube voltage - 5V) / 5mA

For designs requiring a large input voltage variation,

choose the current-limiting diode D4 in Figure 19.

7) Choose RSENSE using the following formula:

RSENSE = 0.25V / (IFAST)

8) Consult Tables 2 and 3 to set pin-straps before

applying power. For example, to fast charge at a

rate of C/2, set the timeout to between 1.5x or 2x the

charge period, three or four hours, respectively.

6 _______________________________________________________________________________________

Share Link: