MC10E212 데이터 시트보기 (PDF) - ON Semiconductor
부품명
상세내역
제조사
MC10E212 Datasheet PDF : 7 Pages
| |||
MC10E212, MC100E212
MAXIMUM RATINGS (Note 1)
Symbol
Parameter
Condition 1
Condition 2
VCC
PECL Mode Power Supply
VEE
NECL Mode Power Supply
VI
PECL Mode Input Voltage
NECL Mode Input Voltage
Iout
Output Current
VEE = 0 V
VCC = 0 V
VEE = 0 V
VCC = 0 V
Continuous
Surge
VI VCC
VI VEE
TA
Operating Temperature Range
Tstg
Storage Temperature Range
θJA
Thermal Resistance (Junction to Ambient) 0 LFPM
500 LFPM
28 PLCC
28 PLCC
θJC
Thermal Resistance (Junction to Case)
std bd
VEE
PECL Operating Range
NECL Operating Range
28 PLCC
Tsol
Wave Solder
<2 to 3 sec @ 248°C
1. Maximum Ratings are those values beyond which device damage may occur.
Rating
8
−8
6
−6
50
100
0 to +85
−65 to +150
63.5
43.5
22 to 26
4.2 to 5.7
−5.7 to −4.2
265
Units
V
V
V
V
mA
mA
°C
°C
°C/W
°C/W
°C/W
V
V
°C
10E SERIES PECL DC CHARACTERISTICS VCCx= 5.0 V; VEE= 0.0 V (Note 1)
0°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
Power Supply Current
80
96
80
96
80
96
mA
VOH
Output HIGH Voltage (Note 2)
3980 4070 4160 4020 4105 4190 4090 4185 4280 mV
VOL
Output LOW Voltage (Note 2)
3050 3210 3370 3050 3210 3370 3050 3227 3405 mV
VIH
Input HIGH Voltage
3830 3995 4160 3870 4030 4190 3940 4110 4280 mV
VIL
Input LOW Voltage
3050 3285 3520 3050 3285 3520 3050 3302 3555 mV
IIH
Input HIGH Current
150
150
150 μA
IIL
Input LOW Current
0.5 0.3
0.5 0.25
0.3 0.2
μA
NOTE: Devices are designed to meet the DC specifications shown in the above table, after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained.
1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.46 V / −0.06 V.
2. Outputs are terminated through a 50 ohm resistor to VCC−2 volts.
10E SERIES NECL DC CHARACTERISTICS VCCx= 0.0 V; VEE= −5.0 V (Note 1)
0°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
Power Supply Current
80
96
80
96
80
96
mA
VOH
Output HIGH Voltage (Note 2)
−1020 −930 −840 −980 −895 −810 −910 −815 −720 mV
VOL
Output LOW Voltage (Note 2)
−1950 −1790 −1630 −1950 −1790 −1630 −1950 −1773 −1595 mV
VIH
Input HIGH Voltage
−1170 −1005 −840 −1130 −970 −810 −1060 −890 −720 mV
VIL
Input LOW Voltage
−1950 −1715 −1480 −1950 −1715 −1480 −1950 −1698 −1445 mV
IIH
Input HIGH Current
150
150
150 μA
IIL
Input LOW Current
0.5 0.3
0.5 0.065
0.3 0.2
μA
NOTE: Devices are designed to meet the DC specifications shown in the above table, after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained.
1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.46 V / −0.06 V.
2. Outputs are terminated through a 50 ohm resistor to VCC−2 volts.
http://onsemi.com
3
Share Link: 