MC100LVEL37(2000) 데이터 시트보기 (PDF) - ON Semiconductor
부품명
상세내역
제조사
MC100LVEL37 Datasheet PDF : 8 Pages
| |||
MC100LVEL37
LVPECL DC CHARACTERISTICS VCC= 3.3 V; VEE= 0.0 V (Note 1)
–40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VIHCMR
Power Supply Current
38
50
38
55
38
55
mA
Output HIGH Voltage (Note 2.)
2215 2295 2420 2275 2345 2420 2275 2345 2420 mV
Output LOW Voltage (Note 2.)
1470 1605 1745 1490 1595 1680 1490 1595 1680 mV
Input HIGH Voltage (Single Ended)
2135
2420 2135
2420 2135
2420 mV
Input LOW Voltage (Single Ended)
1490
1825 1490
1825 1490
1825 mV
Input HIGH Voltage Common Mode
Range (Differential) (Note 3.)
Vpp < 500 mV 1.3
Vpp y 500 mV 1.5
2.9 1.2
2.9 1.4
2.9 1.2
2.9 1.4
2.9
V
2.9
V
IIH
Input HIGH Current
IIL
Input LOW Current
CLKn 0.5
CLKn –300
150
0.5
–300
150
0.5
–300
150 µA
µA
µA
NOTE: Devices are designed to meet the DC specifications shown in the above table, after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained.
1. Input and output parameters vary 1:1 with VCC. VEE can vary ±0.3 V.
2. Outputs are terminated through a 50 ohm resistor to VCC–2 volts.
3. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal.
Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V.
LVNECL DC CHARACTERISTICS VCC= 0.0 V; VEE= –3.3 V (Note 1.)
–40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VIHCMR
Power Supply Current
38
50
38
55
38
55
mA
Output HIGH Voltage (Note 2.)
–1085 –1005 –880 –1025 –955 –880 –1025 –955 –880 mV
Output LOW Voltage (Note 2.)
–1830 –1695 –1555 –1810 –1705 –1620 –1810 –1705 –1620 mV
Input HIGH Voltage (Single Ended)
–1165
–880 –1165
–880 –1165
–880 mV
Input LOW Voltage (Single Ended)
–1810
–1475 –1810
–1475 –1810
–1475 mV
Input HIGH Voltage Common Mode
Range (Differential) (Note 3.)
Vpp < 500 mV –2.0
Vpp y 500 mV –1.8
–0.4 –2.1
–0.4 –1.9
–0.4 –2.1
–0.4 –1.9
–0.4 V
–0.4 V
IIH
Input HIGH Current
IIL
Input LOW Current
CLKn 0.5
CLKn –300
150
0.5
–300
150
0.5
–300
150 µA
µA
µA
NOTE: Devices are designed to meet the DC specifications shown in the above table, after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained.
1. Input and output parameters vary 1:1 with VCC. VEE can vary ±0.3 V.
2. Outputs are terminated through a 50 ohm resistor to VCC–2 volts.
3. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal.
Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V.
http://onsemi.com
3
Share Link: 