MC10E1651(2002) 데이터 시트보기 (PDF) - ON Semiconductor
부품명
상세내역
제조사
MC10E1651 Datasheet PDF : 12 Pages
| |||
MC10E1651
MAXIMUM RATINGS (Note 1)
Symbol
Parameter
Condition 1
Condition 2
VSUP
VPP
Total Supply Voltage
Differential Input Voltage
|VEE| + |VCC|
|V1 – V2|
Iout
Output Current
Continuous
Surge
TA
Operating Temperature Range
Tstg
Storage Temperature Range
θJA
Thermal Resistance (Junction to Ambient) 0 LFPM
500 LFPM
28 PLCC
28 PLCC
θJC
VEE
Thermal Resistance (Junction to Case)
PECL Operating Range
NECL Operating Range
std bd
28 PLCC
Tsol
Wave Solder
<2 to 3 sec @ 248°C
1. Maximum Ratings are those values beyond which device damage may occur.
Rating
12.0
3.7
50
100
0 to +85
–65 to +150
63.5
43.5
22 to 26
4.2 to 5.7
–5.7 to –4.2
265
Units
V
V
mA
mA
°C
°C
°C/W
°C/W
°C/W
V
V
°C
DC CHARACTERISTICS VCC = +5.0 V ±5%; VEE = –5.2 V ±5% (Note 2)
0°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
VOH
VOL
VIL
VIH
II
IIH
Output HIGH Voltage (Note 3)
Output Low Voltage (Note 3)
Input LOW Voltage (LEN)
Input HIGH Voltage (LEN)
Input Current (V1, V2)
Input HIGH Current (LEN)
–1020
–1950
–1.95
–1.17
–840 –980
–1630 –1950
–1.48 –1.95
–0.84 –1.13
65
150
–810 –920
–1630 –1950
–1.48 –1.95
–0.81 –1.07
65
150
–735 mV
–1600 mV
–1.45 mV
–0.735 mV
65
µA
150
ICC
IEE
VCMR
Positive Supply Current
Negative Supply Current
Common Mode Range (Note 4)
50
50
50
mA
–55
–55
–55
–2.0
3.0 –2.0
3.0 –2.0
3.0
V
Hys
Hysteresis
27
27
30
mV
Vskew
Cin
Hysteresis Skew (Note 5)
Input Capacitance
DIP
PLCC
–1.0
3
2
–1.0
3
2
0
mV
pF
3
2
NOTE: Devices are designed to meet the DC specifications shown in the above table, after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained.
2. Input and output parameters vary 1:1 with VCC.
3. Outputs are terminated through a 50 ohm resistor to GND–2 volts.
4. VCMR Min varies 1:1 with VEE; Max varies 1:1 with VCC.
5. Hysteresis skew (Vskew) is provided to indicate the offset of the hysteresis window. For example, at 25°C the nominal hysteresis value is
27mV and the Vskew value indicates that the hysteresis was skewed from the reference level by 1mV in the negative direction. Hence the
hysteresis window ranged from 14mV below the reference level to 13mV above the reference level. All hysteresis measurements were
determined using a reference voltage of 0mV.
http://onsemi.com
3
Share Link: 