MC10E1651 데이터 시트보기 (PDF) - ON Semiconductor
부품명
상세내역
제조사
MC10E1651 Datasheet PDF : 10 Pages
| |||
MC10E1651
Table 3. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
Condition 2
Rating
Unit
VSUP
VPP
VI
Iout
Total Supply Voltage
Differential Input Voltage
Input Voltage
Output Current
|VEE| + |VCC|
|V1 − V2|
Continuous
Surge
12.0
V
3.7
V
VEE v VI v VCC
V
50
mA
100
mA
TA
Operating Temperature Range
Tstg
Storage Temperature Range
qJA
Thermal Resistance (Junction−to−Ambient) 0 lfpm
500 lfpm
28 PLCC
28 PLCC
0 to +85
−65 to +150
63.5
43.5
°C
°C
°C/W
°C/W
qJC
Thermal Resistance (Junction−to−Case) Standard Board
28 PLCC
VEE
Operating Range
GND = 0 V
Tsol
Wave Solder
Pb v 3 sec @ 248°C
Pb−Free v 3 sec @ 260°C
22 to 26
−4.2 to −5.7
265
265
°C/W
V
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
Table 4. DC CHARACTERISTICS VCC = +5.0 V ±5%; VEE = −5.2 V ±5%, VCC = 0 V (Note 1)
0°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
VOH
Output HIGH Voltage (Note 1)
VOL
Output Low Voltage (Note 1)
VIL
Input LOW Voltage (LEN) (Note 1)
VIH
Input HIGH Voltage (LEN) (Note 1)
II
Input Current (V1, V2)
IIH
Input HIGH Current (LEN)
−1020
−1950
−1.95
−1.17
−840 −980
−1630 −1950
−1.48 −1.95
−0.84 −1.13
65
150
−810 −920
−1630 −1950
−1.48 −1.95
−0.81 −1.07
65
150
−735 mV
−1600 mV
−1.45 mV
−0.735 mV
65
mA
150
ICC
Positive Supply Current
IEE
Negative Supply Current
50
50
50
mA
−55
−55
−55
VCMR Common Mode Range (Note 2)
−2.0
3.0 −2.0
3.0 −2.0
3.0
V
Hys
Hysteresis
27
27
30
mV
Vskew
Cin
Hysteresis Skew (Note 3)
Input Capacitance
DIP
PLCC
−1.0
3
2
−1.0
3
2
0
mV
pF
3
2
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input VIL and VIH parameters vary 1:1 with VCC. Output VOH and VOL parameters vary 1:1 with GND.
2. VCMR Min varies 1:1 with VEE; Max varies 1:1 with VCC.
3. Hysteresis skew (Vskew) is provided to indicate the offset of the hysteresis window. For example, at 25°C the nominal hysteresis value is
27 mV and the Vskew value indicates that the hysteresis was skewed from the reference level by 1mV in the negative direction. Hence the
hysteresis window ranged from 14 mV below the reference level to 13 mV above the reference level. All hysteresis measurements were
determined using a reference voltage of 0 mV.
http://onsemi.com
3
Share Link: 