MC44605P 데이터 시트보기 (PDF) - ON Semiconductor
부품명
상세내역
제조사
MC44605P
ON Semiconductor
MC44605P Datasheet PDF : 20 Pages
| |||
MC44605
MAXIMUM RATINGS
Rating
Pin #
Symbol
Value
Unit
Total Power Supply and Zener Current
Output Supply Voltage with Respect to Ground
(ICC + IZ)
2
VC
1
VCC
40
mA
18
V
Output Current
Source
Sink
3
mA
IO(Source)
IO(Sink)
−750
750
Output Energy (Capacitive Load per Cycle)
W
5.0
mJ
Soft−Start
Current Sense, Voltage Feedback, E/A Output, CT, Rref, MPL, OHD, Cext, WSCD
E.H.T.OVP, Sync Input Current
VSS
−0.3 to 2.2 V V
Vin
−0.3 to 5.5 V V
mA
Source
9
6
Isync (Source)
IEHT (Source)
−4.0
Sink
9
Isync (Sink)
6
IEHT (Sink)
10
Demagnetization Detection Input Current
Source
Sink
8
mA
Idemag−ib (Source)
Idemag−ib (Sink)
−4.0
10
Error Amplifier Output Sink Current
13
IE/A (Sink)
20
mA
Power Dissipation and Thermal Characteristics
Maximum Power Dissipation at TA = 85°C
Thermal Resistance, Junction−to−Air
PD
RqJA
0.6
W
100
°C/W
Operating Junction Temperature
TJ
150
°C
Operating Ambient Temperature
TA
−25 to +85 °C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
ELECTRICAL CHARACTERISTICS (VCC and VC = 12 V, Rref = 10 kW, CT = 2.2 nF, for typical values TA = 25°C, for
min/max values TA = −25° to +85°C unless otherwise noted.) (Note 1)
Characteristic
Pin # Symbol Min
Typ
Max
Unit
OUTPUT SECTION (Note 2)
Output Voltage (Note 3)
Low Level Drop Voltage
High Level Drop Voltage
(ISink = 100 mA)
(ISink = 500 mA)
(ISource = 200 mA)
(ISource = 500 mA)
3
V
VOL
−
1.0
1.2
−
1.4
2.0
VOH
−
1.5
2.0
−
2.0
2.7
Output Voltage During Initialization Phase
VCC − 0 to 1.0 V, ISink = 10 mA
VCC − 1.0 to 5.0 V, ISink = 100 mA
VCC − 5.0 to 13 V, ISink = 1.0 mA
3
VOL
−
−
V
1.0
−
0.1
1.0
−
0.1
1.0
Output Voltage Rising Edge Slew−Rate (CL = 1.0 nF, TJ = 25°C)
dVo/dT
−
300
−
V/ms
Output Voltage Falling Edge Slew−Rate (CL = 1.0 nF, TJ = 25°C)
dVo/dT
−
−300
−
V/ms
1. Adjust VCC above the startup threshold before setting to 12 V. Low duty cycle pulse techniques are used during test to maintain junction
temperature as close to ambient as possible.
2. No output signal when the Error Amplifier output is in Low State, i.e., when for instance, VFB = 2.7 V.
3. VC must be greater than 5.0 V.
http://onsemi.com
3
Share Link: