44608 데이터 시트보기 (PDF) - ON Semiconductor
부품명
상세내역
제조사
44608 Datasheet PDF : 16 Pages
| |||
MC44608
PIN FUNCTION DESCRIPTION
Pin
Name
Description
1
Demag
The Demag pin offers 3 different functions: Zero voltage crossing detection (50 mV), 24 mA current detection
and 120 mA current detection. The 24 mA level is used to detect the secondary reconfiguration status and the
120 mA level to detect an Over Voltage status called Quick OVP.
2
Isense
The Current Sense pin senses the voltage developed on the series resistor inserted in the source of the
power MOSFET. When Isense reaches 1.0 V, the Driver output (pin 5) is disabled. This is known as the Over
Current Protection function. A 200 mA current source is flowing out of the pin 3 during the start−up phase and
during the switching phase in case of the Pulsed Mode of operation. A resistor can be inserted between the
sense resistor and the pin 2, thus a programmable peak current detection can be performed during the SMPS
stand−by mode.
3
Control Input A feedback current from the secondary side of the SMPS via the Opto−coupler is injected into this pin. A
resistor can be connected between this pin and GND to allow the programming of the Burst duty cycle during
the Stand−by mode.
4
Ground
This pin is the ground of the primary side of the SMPS.
5
Driver
The current and slew rate capability of this pin are suited to drive Power MOSFETs.
6
VCC
This pin is the positive supply of the IC. The driver output gets disabled when the voltage becomes higher
than 15 V and the operating range is between 6.6 V and 13 V. An intermediate voltage level of 10 V creates a
disabling condition called Latched Off phase.
7
This pin is to provide isolation between the Vi pin 8 and the VCC pin 6.
8
Vi
This pin can be directly connected to a 500 V voltage source for start−up function of the IC. During the
Start−up phase a 9.0 mA current source is internally delivered to the VCC pin 6 allowing a rapid charge of the
VCC capacitor. As soon as the IC starts−up, this current source is disabled.
OPERATING DESCRIPTION
Regulation
V CC
V LP−stby
Control
Input
10
S3
3
&
Stand−by
Latched off Phase
10
S2
Vdd
Switching Phase
20 W
Regulation
Output
PWM
Comparator
5V
4 kHz
Filter
1.6 V
Figure 2. Regulator
The switch S3 is closed in Stand−by mode during the
Latched Off Phase while the switch S2 remains open. (See
section PULSED MODE DUTY CYCLE CONTROL).
The resistor Rdpulsed (Rduty cycle burst) has no effect on
the regulation process. This resistor is used to determine the
burst duty cycle described in the chapter “Pulsed Duty Cycle
Control” on page 8.
PWM Latch
The MC44608 works in voltage mode. The on−time is
controlled by the PWM comparator that compares the
oscillator sawtooth with the regulation block output (refer to
the block diagram on page 2).
The PWM latch is initialized by the oscillator and is reset
by the PWM comparator or by the current sense comparator
in case of an over current. This configuration ensures that
only a single pulse appears at the circuit output during an
oscillator cycle.
The pin 3 senses the feedback current provided by the
Opto coupler. During the switching phase the switch S2 is
closed and the shunt regulator is accessible by the pin 3. The
shunt regulator voltage is typically 5.0 V. The dynamic
resistance of the shunt regulator represented by the zener
diode is 20 W. The gain of the Control input is given on
Figure 11 which shows the duty cycle as a function of the
current injected into the pin 3.
A 4.0 kHz filter network is inserted between the shunt
regulator and the PWM comparator to cancel the high
frequency residual noise.
Current Sense
The inductor current is converted to a positive voltage by
inserting a ground reference sense resistor RSense in series
with the power switch.
The maximum current sense threshold is fixed at 1.0 V.
The peak current is given by the following equation:
Ipkmax
+
1
Rsense(W)
(A)
http://onsemi.com
5
Share Link: 