ML7041 데이터 시트보기 (PDF) - Oki Electric Industry

부품명

상세내역

제조사

ML7041

Audio CODEC

Oki Electric Industry 

OKI Semiconductor

FEDL7041-04

ML7041

SG

Analog signal ground.

The output voltage of this pin is approximately 1.4 V. Put the bypass capacitors 0.1 µF ceramic type between this

pin and GND to get the specified noise characteristics. During power-down, this output voltage is 0 V.

SWA, SWB, SWC

Used for an internal analog switch. The pin SWB is connected to the pin SWA or the pin SWC. This is controlled

by CR1-B1.

RG1PDN, RG1IN, RG1O

Used for Regulator 1. The RG1PDN pin is a power down input. When set to “L”, the Regulator 1 changes to the

power down state. Since the power down is controlled by a logical OR with CR5-B4 of the control register, set

CR5-B4 to logic “0” when using this pin. The RG1IN pin is input to the Regulator 1. The RG1O pin is output from

the Regulator 1, whose voltage is 3.0 V. A 1 µF ceramic type bypass capacitor must be connected between the

power input pin and GND, and a 10 µF tantalum bypass capacitor must be connected from the output pin to GND.

RG2PDN, RG2IN, RG2O

Used for Regulator 2. The RG2PDN pin is a power down input. When set to “L”, the Regulator 2 changes to the

power down state. Since the power down is controlled by a logical OR with CR5-B5 of the control register, set

CR5-B5 to logic “0” when using this pin. The RG2IN pin is the input to the Regulator 2. The RG2O pin is the

output from the Regulator 2, whose voltage is 3.0 V. A 1 µF ceramic type bypass capacitor must be connected

between the power input pin and GND, and a 10 µF tantalum bypass capacitor must be connected from the output

pin to GND.

Note1: The RG1O and RG2O outputs must not be used as the 3 V supply for the ML7041.

Note2: The RG1IN and RG2IN should be common near the device and supplied from the same power supply.

GP1, GP2, GP3, GP4

General purpose driver output. Each pin is controlled by CR5-B1 through CR5-B4. By selecting CR5-B7, the GP1

pin can be controlled by the receive side sign bit.

VDD, VA, VA1, VA2, VA3

VDD is the digital power supply. VA, VA1, VA2, and VA3 are the analog power supply pins. Since these pins are

separated in the device, connect them as close as possible on the PCB.

DG, AG, AG1, AG2, AG3, AGR1, AGR2, AGGP1, AGGP2

Ground. DG is the digital ground. AG, AG1, AG2, AG3, AGR1, AGR2, AGGP1 and AGGP2 are the analog

ground. Since these pins are separated in the device, connect them as close as possible on the PCB.

PDN

Power down and reset control input.

When set to digital “L”, the device changes to the power down state and the control register is reset. Since the

power down mode is controlled by a logical OR with CR0-B5 of the control register, set CR0-B5 to logic “0” when

using this pin. The reset pulse width must be 200 ns or more. Be sure to reset the control register after turning on

the power.

MCK

Master clock input.

The frequency must be 2.048 MHz. MCK can be asynchronous with SYNC and BCLK.

If a frequency of BCLK is 2.048 MHz, the BCLK can be shared with MCK.

BCLK

Shift clock input for the PCM data.

The frequency is set in the range of 64 kHz to 2048 kHz for A/µ-law PCM data and set in the range of 128 kHz to

2048 kHz for linear code selection.

7/28

Share Link: