MT9173AN1 데이터 시트보기 (PDF) - Zarlink Semiconductor Inc

부품명

상세내역

제조사

MT9173AN1

ISO2-CMOS ST-BUS™ FAMILY Digital Subscriber Interface Circuit with RxSB Digital Network Interface Circuit with RxSB

Zarlink Semiconductor Inc 

MT9173/74

Data Sheet

The overall mode of operation of the DNIC can be programmed to be either a baseband modem (MOD mode) or a

digital network transceiver (DN mode). As a baseband modem, transmit/receive data is passed transparently

through the device at 80 or 160 kbit/s by the DV port. The CD port transfers the C-channel and D-Channel also at

80 or 160 kbit/s.

In DN mode, both the DV and CD ports operate as ST-BUS streams at 2.048 Mbit/s. The DV port transfers data

over pins DSTi and DSTo while on the CD port, the CDSTi and CDSTo pins are used. The SINGL port option only

exists in DN mode.

In MOD mode, DUAL port operation must be used and the D, B1 and B2 channel designations no longer exist. The

selection of SLV or MAS will determine which of the DNICs is using the externally supplied clock and which is

phase locking to the data on the line. Due to jitter and end to end delay, one end must be the master to generate all

the timing for the link and the other must extract the timing from the receive data and synchronize itself to this timing

in order to recover the synchronous data. DUAL port mode allows the user to use two separate serial busses: the

DV port for PCM/data (B channels) and the CD port for control and signalling information (C and D channels). In the

SINGL port mode, all four channels are concatenated into one serial stream and input to the DNIC via the DV port.

The order of the C and D channels may be changed only in DN/DUAL mode. The DNIC may be configured to

transfer the D-channel in channel 0 and the C-channel in channel 16 or vice versa. One other feature exists; ODE,

where both the DV and CD ports are tristated in order that no devices are damaged due to excessive loading while

all DNICs are in a random state on power up in a daisy chain arrangement.

DV Port (DSTi/Di, DSTo/Do)

The DV port transfers data or PCM encoded voice to and from the line according to the particular mode selected by

the mode select pins. The modes affecting the configuration of the DV port are MOD or DN and DUAL or SINGL. In

DN mode the DV port operates as an ST-BUS at 2.048 Mbit/s with 32, 8 bit channels per frame as shown in Figure

9. In this mode the DV port channel configuration depends upon whether DUAL or SINGL port is selected. When

DUAL port mode is used, the C and D channels are passed through the CD port and the B1 and B2 channels are

passed through the DV port. At 80 kbit/s only one channel of the available 32 at the DV port is utilized, this being

channel 0 which carries the B1-channel. This is shown in Figure 3. At 160 kbit/s, two channels are used, these

being 0 and 16 carrying the B1 and B2 channels, respectively. This is shown in Figure 4. When SINGL port mode is

used, channels B1, B2, C and D are all passed via the DV port and the CD port is disabled. See CD port description

for an explanation of the C and D channels.

F0

ST-BUS

Channel Channel Channel Channel

31

0

1

2

125 µsec

••••••••

Channel Channel

29

30

Channel

31

Channel

0

Most

Significant

Bit (First)

Bit 7

Bit 6

Bit 5

Bit 4 Bit 3

3.9 µsec

Bit 2

Bit 1

Bit 0

Least

Significant

Bit (Last)

Figure 9 - ST-BUS Format

The D-channel is always passed during channel time 0 followed by the C and B1 channels in channel times 1 and

2, respectively for 80 kbit/s. See Figure 5. For 160 kbit/s the B2 channel is added and occupies channel time 3 of

the DV port. See Figure 6. For all of the various configurations the bit orders are shown by the respective diagram.

In MOD mode the DV and CD ports no longer operate at 2.048 Mbits/s but are continuous serial bit streams

operating at the bit rate selected of 80 or 160 kbit/s. While in the MOD mode only DUAL port operation can be used.

10

Zarlink Semiconductor Inc.

Share Link: