NB100LVEP224(2003) 데이터 시트보기 (PDF) - ON Semiconductor
부품명
상세내역
제조사
NB100LVEP224
(Rev.:2003)
(Rev.:2003)
ON Semiconductor
NB100LVEP224 Datasheet PDF : 10 Pages
| |||
NB100LVEP224
LVPECL DC CHARACTERISTICS VCC = 2.5 V; VEE = 0 V (Note 3)
-40 °C
25°C
85°C
Symbol
IEE
VOH
VOL
VIH
Characteristic
Power Supply Current
Output HIGH Voltage (Note 8)
Output LOW Voltage (Note 8)
Input HIGH Voltage (Single-Ended)
(Note 9)
Min Typ Max Min Typ Max Min Typ Max Unit
130 160 195 135 165 200 140 165 205 mA
1355 1480 1605 1355 1480 1605 1355 1480 1605 mV
555 680 900 555 680 900 555 680 900 mV
1335
1620 1335
1620 1275
1620 mV
VIL
Input LOW Voltage (Single-Ended)
555
(Note 9)
900 555
900 555
900 mV
VIHCMR
IIH
IIL
Input HIGH Voltage Common Mode
Range (Differential) (Note 10)
CLK/CLK
Input HIGH Current
Input LOW Current
CLK
CLK
1.2
0.5
-150
2.5 1.2
150
0.5
-150
2.5 1.2
150
0.5
-150
2.5
V
150 mA
mA
NOTE: 100LVEP circuits are designed to meet the DC specifications shown in the above table, after thermal equilibrium has been
established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is
maintained.
3. Input and output parameters vary 1:1 with VCC. VEE can vary + 0.125 V to -1.3 V.
4. All outputs loaded with 50 W to VCC - 2.0 V.
5. Do not use VBB at VCC < 3.0 V.
6. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differen-
tial input signal.
LVPECL DC CHARACTERISTICS VCC = 3.3 V; VEE = 0 V (Note 7)
-40 °C
25°C
85°C
Symbol
IEE
VOH
VOL
VIH
VIL
Characteristic
Power Supply Current
Output HIGH Voltage (Note 8)
Output LOW Voltage (Note 8)
Input HIGH Voltage (Single-Ended)
(Note 9)
Input LOW Voltage (Single-Ended)
(Note 9)
Min Typ Max Min Typ Max Min Typ Max Unit
140 165 195 145 175 205 145 175 210 mA
2155 2280 2405 2155 2280 2405 2155 2280 2405 mV
1355 1480 1700 1355 1480 1700 1355 1480 1700 mV
2135
2420 2135
2420 2135
2420 mV
1355
1700 1355
1700 1355
1700 mV
VIHCMR Input HIGH Voltage Common Mode
1.2
Range (Differential) (Note 10) (Figure
5)
3.3 1.2
3.3 1.2
3.3
V
IIH
Input HIGH Current
IIL
Input LOW Current
CLK 0.5
CLK -150
150
0.5
-150
150
0.5
-150
150 mA
mA
NOTE: 100LVEP circuits are designed to meet the DC specifications shown in the above table, after thermal equilibrium has been established.
The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained.
7. Input and output parameters vary 1:1 with VCC. VEE can vary +0.925 V to -0.5 V.
8. All outputs loaded with 50 W to VCC - 2.0 V.
9. Single ended input operation is limited VCC ≥ 3.0 V in LVPECL mode.
10. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
http://onsemi.com
4
Share Link: