PCD5013H/F1 데이터 시트보기 (PDF) - Philips Electronics

부품명

상세내역

제조사

PCD5013H/F1

FLEX™roaming decoder II

Philips Electronics 

Philips Semiconductors

FLEX™ roaming decoder II

Product specification

PCD5013

8.4.7 CONTROL PACKET (ID = 02H)

The control packet defines a number of different control

bits for the PCD5013.

FF: force frame 0 to 7 (Table 12). When set, each of these

bits forces the PCD5013 to decode one of the FLEX™

frames 0 to 7 irrespective of the system collapse value (for

details of collapse values see Section 8.6.2). For example,

if the system collapse causes the PCD5013 to decode

frames 0, 32, 64 and 96, setting FF2 causes the PCD5013

to also decode FLEX™ frame 2. This may be used to

acquire transmitted time information or channel attributes

(e.g. Local ID). Value after reset = 0.

SPM: single phase mode (Table 12). When this bit is set,

the PCD5013 decodes only one of the transmitted phases.

When this bit is clear, the PCD5013 decodes all

transmitted phases. This value is determined by the

CAPCODE (Section 8.6). A change to this bit while the

PCD5013 is on does not take effect until the next block 0

of a frame. Value after reset = 0.

PS: phase select (Tables 11 and 12). When the SPM bit is

set, these bits define which phase the PCD5013 shall

decode. This value is determined by the CAPCODE

(Section 8.6). A change to these bits, while the PCD5013

is on, does not take effect until the next block 0 of a frame.

Value after reset = 0.

Table 11 Phase selection (by PS bits)

DECODED PHASE (BASED ON

PS1 PS0

FLEX™ DATA RATE)

1600 bits/s 3200 bits/s 6400 bits/s

0

0

A

A

A

0

1

A

A

B

1

0

A

C

C

1

1

A

C

D

SBI: send block information words (BIW) 2 to 4

(Table 12). When this bit is set, BIWs with time and date

information and BIWs received in error are sent to the host,

(Section 8.7.9). Value after reset = 0.

MTC: minute timer clear (Table 12). Setting this bit causes

the 1-minute timer to restart from 0 (Section 8.4.8).

ON: turn on decoder (Table 12). When this bit is set, the

PCD5013 decodes FLEX™ signals. If this bit is cleared,

signal processing stops. However, to assure proper

operation, the PCD5013 requires that it be set into

asynchronous mode when turned off. To achieve that the

following sequence must be used:

1. Send control packet with ON bit clear (decoder off)

2. Send control packet with ON bit set (decoder on)

3. Send control packet with ON bit clear (decoder off).

Timing between these steps is specified below and is

measured from the positive edge of the last clock of one

packet to the positive edge of the last clock of the next

packet.

• The minimum time between steps 1 and 2 is the greater

of 2 ms or the programmed shut-down time.

The programmed shut-down time is the sum of all of the

times programmed in the used receiver shut-down

settings packets.

• There is no maximum time between steps 1 and 2.

• The minimum time between steps 2 and 3 is 2 ms.

• The maximum time between steps 2 and 3 is the

programmed warm-up time minus 2 ms.

The programmed warm-up time is the sum of all the

times programmed in the used receiver warm-up

settings packets.

EAE: end of addresses enable. When this bit is set, the EA

bit in the Status Packet is PCD5013 set immediately after

the PCD5013 decodes the last address word in the frame

if any of the enabled PCD5013 addresses was detected in

the frame. When this bit is cleared, the EA bit is never set.

Table 12 Control packet bit assignments

BYTE

3

2

1

0

BIT 7

0

FF7

0

0

BIT 6

0

FF6

SPM

SBI

BIT 5

0

FF5

PS1

0

BIT 4

0

FF4

PS0

MTC

BIT 3

0

FF3

0

0

BIT 2

0

FF2

0

0

BIT 1

1

FF1

0

EAE

BIT 0

0

FF0

0

ON

1999 Apr 12

21

Share Link: