MICRF002BN 데이터 시트보기 (PDF) - Micrel

부품명

상세내역

제조사

MICRF002BN

QwikRadio™ Low Power UHF Receiver

Micrel 

MICRF002

I/O Pin Interface Circuitry

QwikRadio tm

3. CAGC Pin

Micrel

Interface circuitry for the various I/O pins of the MICRF002 is

shown in Figures 1 through 6. Specific information

regarding each of these circuits is discussed in the following

sub-paragraphs. Not shown are ESD protection diodes

which are applied to all input and output pins.

1. ANT Pin

Figure 3 illustrates the CAGC pin interface circuit. The AGC

control voltage is developed as an integrated current into a

capacitor CAGC. The attack current is nominally 15µA,

while the decay current is a 1/10th scaling of this, nominally

1.5µA, so the attack/decay timeconstant ratio is fixed at

10:1. Signal gain of the RF/IF strip inside the IC diminishes

as the voltage on CAGC decreases. Further discussion on

setting the attack time constant is found in “Application Note

TBD. Modification of the attack/decay ratio is possible by

adding resistance from CAGC pin either to VDDBB or

VSSBB, as desired.

Both the Push and Pull current sources are disabled during

SHUT, which holds the voltage across CAGC, and improves

recovery time in duty-cycled applications. To further

improve duty cycle recovery, both Push and Pull currents

are increased by 45X for approximately 10msec after

release of SHUT. This allows rapid recovery of any voltage

droop on CAGC while in SHUT.

Figure 1 ANT Pin

The ANT pin is internally AC-coupled via a 3pF capacitor, to

an RF N-channel MOSFET, as shown in Figure 1.

Impedance on this pin to VSS is quite high at low

frequencies, and decreases as frequency increases. In the

UHF frequency range, the device input can be modeled as

6.3kΩ in parallel with 2pF (pin capacitance) shunt to

VSSRF.

2. CTH Pin

Figure 2 illustrates the CTH pin interface circuit. CTH pin is

driven from a P-channel MOSFET source-follower biased

with approximately 10µA of bias current. Transmission

gates TG1 and TG2 isolate the 6.9pF capacitor. Internal

control signals PHI1/PHI2 are related in a manner such that

the impedance across the transmission gates looks like a

“resistance” of approximately 100kΩ. The DC potential on

the CTH pin is approximately 1.6V

4. DO and WAKEB Output Pins

The output stage for the signals DO and WAKEB is shown in

Figure 4. The output is a 10µA push-10µA pull, switched

current stage. Such an output stage is capable of driving

CMOS-type loads.

An external buffer-driver is

recommended for driving high capacitance loads.

5. REFOSC Pin

The REFOSC input circuit is shown in Figure 5. Input

impedance is quite high (200kΩ). This is a Colpitts

oscillator, with internal 30pF capacitors. This input is

intended to work with standard ceramic resonators,

connected from this pin to VSSBB, although a crystal may

be used instead, where greater frequency accuracy is

required. The resonators should not contain integral

capacitors, since these capacitors are contained inside the

IC. Externally applied signals should be AC-coupled,

amplitude limited to approximately 0.5Vpp. The nominal DC

bias voltage on this pin is 1.4V.

6. Control Inputs (SEL0, SEL1, SWEN, SHUT)

Control input circuitry is shown in Figures 6a and 6b. The

standard input is a logic inverter constructed with minimum

geometry MOSFETs (Q2, Q3). P-channel MOSFET Q1 is a

large channel length device which functions essentially as a

“weak” pullup to VDDBB. Typical pullup current is 5µA,

leading to an impedance to the VDDBB supply of typically

1MΩ.

July 1999

11

MICRF002

Share Link: