DatasheetQ Logo
Electronic component search and free download site. Transistors,MosFET ,Diode,Integrated circuits

HI-3282CLT 데이터 시트보기 (PDF) - Holt Integrated Circuits

부품명
상세내역
제조사
HI-3282CLT
Holt
Holt Integrated Circuits Holt
HI-3282CLT Datasheet PDF : 14 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
HI-3282, HI-3282B
FUNCTIONAL DESCRIPTION (cont.)
BIT TIMING
The ARINC 429 specification contains the following timing
specification for the received data:
HIGH SPEED LOW SPEED
BIT RATE
100K BPS ± 1% 12K -14.5K BPS
(HI-3282BPJx-xx only - 6.5K BPS min.)
PULSE RISE TIME 1.5 ± 0.5 µsec 10 ± 5 µsec
PULSE FALL TIME 1.5 ± 0.5 µsec 10 ± 5 µsec
PULSE WIDTH
5 µsec ± 5% 34.5 to 41.7 µsec
(HI-3282BPJx-xx only - 76.9 µsec max.)
RECEIVER PARITY
The 32nd bit of received ARINC words stored in the receive FIFO
is used as a Parity Flag indicating whether good Odd parity is re-
ceived from the incoming ARINC word.
Odd Parity Received
The parity bit is reset to indicate correct parity was received
and the resulting word is then written to the receive FIFO.
Even Parity Received
The receiver sets the 32nd bit to a “1”, indicating a parity error
and the resulting word is then written to the receive FIFO.
Therefore, the 32nd bit retrieved from the receiver FIFO will always
be a “0” when valid (odd parity) ARINC 429 words are received.
data ready flag flip flop to a "1", D/R1 or D/R2 (or both) will go low.
The data flag for a receiver will remain low until after both ARINC
bytes from that receiver are retrieved. This is accomplished by
activating EN with SEL, the byte selector, low to retrieve the first
byte and activating EN with SEL high to retrieve the second byte.
EN1 retrieves data from receiver 1 and EN2 retrieves data from
receiver 2. If another ARINC word is received and a new EOS
occurs before the two bytes are retrieved, the data is overwritten
by the new word.
INTERNAL LIGHTNING PROTECTION (-10 Only)
The HI-3282-10 configurations are similar to the HI-3282 with the
exception that it allows an external 10K to 15K ohm resistor to be
added in series with each ARINC input without affecting the
ARINC input thresholds. This option is especially useful in
applications where lightning protection circuitry is also required.
The design of the HI-3282-10 device requires the external
10K to 15K ohm series resistors for proper ARINC level detection.
The typical 10 volt differential signal is translated and input to a
window comparator and latch. The comparator levels are set so
that, with the external 10K to 15K ohm resistors, they are just
below the standard 6.5 V minimum ARINC data threshold and just
above the 2.5 V maximum ARINC null threshold.
The receivers of the HI-3282-10 when used with external
15K ohm resistors will withstand DO-160F, Level 3, waveforms 3,
4, 5A and 5B. No additional lightning protection circuit is
necessary.
RETRIEVING DATA
APPLICATION NOTE 300
Once 32 valid bits are recognized, the receiver logic generates an
End of Sequence (EOS). If the receiver decoder is enabled and
the 9th and 10th ARINC bits match the control word program bits
or if the receiver decoder is disabled, then the EOS clocks the
Please refer to the Holt AN-300 Application Note for additional
information and recommendations on lightning protection of Holt
Line Drivers and Receivers.
SEL
EN
D/R
DECODER
CONTROL
BITS
MUX
CONTROL
/
LATCH
ENABLE
CONTROL
BITS 9 & 10
EOS
TO PINS
32 TO 16 DRIVER
CONTROL
BIT BD14
CLOCK
OPTION
32 BIT LATCH
32 BIT SHIFT REGISTER
DATA PARITY
CHECK
BIT CLOCK
32ND
BIT
BIT
COUNTER
AND
END OF
SEQUENCE
EOS
ONES
NULL
SHIFT REGISTER
SHIFT REGISTER
WORD GAP
WORD GAP
TIMER
START
SEQUENCE
CONTROL
BIT CLOCK
END
CLOCK
CLK
ZEROS
SHIFT REGISTER
ERROR
DETECTION
ERROR
CLOCK
FIGURE 2. RECEIVER BLOCK DIAGRAM
HOLT INTEGRATED CIRCUITS
4

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]