ST6232BB6 데이터 시트보기 (PDF) - STMicroelectronics

부품명

상세내역

제조사

ST6232BB6

8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, 16-BIT AUTO-RELOAD TIMER, EEPROM, SPI AND UART

STMicroelectronics 

ST62T32B ST62E32B

1.2 PIN DESCRIPTIONS

VDD and VSS. Power is supplied to the MCU via

these two pins. VDD is the power connection and

VSS is the ground connection.

VDDp and VSSp. Power is supplied to the MCU

I/Os independently from the rest of the chip using

these two pins. These pins have to be connected

to the VDD and VSS pins. It is not allowed to leave

any of these pins unconnected or to apply different

potentials respectively to VDD/VDDp and VSS/VSSp.

AVDD and AVSS. Power is supplied to the

MCUA/D converter independently from the rest of

the chip using these two pins.

OSCin and OSCout. These pins are internally

connected to the on-chip oscillator circuit. A quartz

crystal, a ceramic resonator or an external clock

signal can be connected between these two pins.

The OSCin pin is the input pin, the OSCout pin is

the output pin.

RESET. The active-low RESET pin is used to re-

start the microcontroller.

TEST/VPP. The TEST must be held at VSS for nor-

mal operation. If TEST pin is connected to a

+12.5V level during the reset phase, the

EPROM/OTP programming Mode is entered.

NMI. The NMI pin provides the capability for asyn-

chronous interruption, by applying an external non

maskable interrupt to the MCU. The NMI input is

falling edge sensitive with Schmitt trigger charac-

teristics. The user can select as option the availa-

bility of an on-chip pull-up at this pin.

PA0-PA7. These 8 lines are organised as one I/O

port (A). Each line may be configured under soft-

ware control as inputs with or without internal pull-

up resistors, interrupt generating inputs with pull-

up resistors, open-drain or push-pull outputs.

PA2/OVF, PA3/PWM, PA4/CP1 and PA5/CP2 can

be used respectively as overflow output pin, output

compare pin, and as two input capture pins for the

embedded 16-bit Auto-Reload Timer.

In addition, PA4-PA5 can also be used as analog

inputs for the A/D converter while PA0-PA3 can

sink 20mA for direct LED or TRIAC drive.

PB0,PB3-PB7 These 6 lines are organised as one

I/O port (B). Each line may be configured under

software control as inputs with or without internal

pull-up resistors, interrupt generating inputs with

pull-up resistors, open-drain or push-pull outputs,

analog inputs for the A/D converter.

PC5-PC7. These 3 lines are organised as one I/O

port (C). Each line may be configured under soft-

ware control as input with or without internal pull-

up resistor, interrupt generating input with pull-up

resistor, analog input for the A/D converter, open-

drain or push-pull output.

PD0-PD7. These 8 lines are organised as one I/O

port (portD). Each line may be configured under

software control as input with or without internal

pull-up resistor, interrupt generating input with

pull-up resistor, analog input open-drain or push-

pull output. In adition, the pins PD5/TXD1 and

PD4/RXD1 can be used as UART output

(PD5/TXD1) or UART input (PD4/RXD1). The pins

PD3/Sout, PD2/Sin and PD1/SCL can also be

used respectively as data out, data in and Clock

pins for the on-chip SPI.

PE0-PE4. These 5 lines are organised as one I/O

port (PE). Each line may be configured under soft-

ware control as input with or without internal pull-

up resistor, interrupt generation input with pull-up

resistor, open-drain or push-pull output. In output

mode, these lines can also sink 20mA for direct

LED and TRIAC driving.

TIMER. This is the TIMER 1 I/O pin. In input mode,

it is connected to the prescaler and acts as ex-

ternal timer clock or as control gate for the internal

timer clock. In output mode, the TIMER pin outputs

the data bit when a time-out occurs.The user can

select as option the availability of an on-chip pull-

up at this pin.

7/86

111

Share Link: