ST8016S 데이터 시트보기 (PDF) - Sitronix Technology Co., Ltd.

부품명

상세내역

제조사

ST8016S

COM/SEG LCD Driver

Sitronix Technology Co., Ltd. 

ST8016S

Y1 -Y160

When L/R input is at VDD level "H", ElO1 is set for input, and EIO2 is set for output.

During output, set to "H" while LP • XCK is "H" and after 160 bits of data have been

read, set

to "L” for one cycle (from falling edge to failing edge of XCK), after which it returns to

"H".

During input, the chip is selected while El is set to "L" after the LP signal is input. The

chip is non-selected after 160 bits of data have been read.

LCD drive output pins

Corresponding directly to each bit of the data latch, one level (V0, V12 or V43) is

selected and output.

Table of truth values is shown in "TRUTH TABLE" in Functional Operations.

(Common mode)

SYMBOL

VDD

GND

LGND

VSS

V0L, V0R

V12L, V12R

V43L, V43R

ElO1

EIO2

LP

L/R

/DISPOFF

FR

FUNCTION

Logic system power supply pin

Connected to +2.5 to +5.5 V.

Ground pin

Logic system power ground pin

Do not short LGND with GND and Vss by ITO on LCD panel

Connect it to GND on PCB or FPC.

Connect to GND by ITO on LCD panel.

Bias power supply pins for LCD drive voltage

Normally use the bias voltages set by a resistor divider.

Ensure that voltages are set such that VSS < V43 < V12 < V0.

ViL and ViR (i = 0,12, 43) must connect to an external power supply, and supply regular

voltage that is assigned by specification for each power pin.

Shift data input/output pin for bi-directional shift register

Output pin when L/R is at LGND level "L', input pin when L/R is at VDD level "H".

When L/R = H, ElO1 is used as input pin, it will be pulled down.

When L/R = L, ElO1 is used as output pin, it won't be pulled down.

Refer to section 6.2.2.

Shift data input/output pin for bi-directional shift register

Input pin when L/R is at LGND level "L", output pin when L/R is at VDD level "H".

When L/R = L, EIO2 is used as input pin, it will be pulled down.

When L/R = H, EIO2 is used as output pin, it won't be pulled down.

Refer to section 6.2.2.

Shift clock pulse input pin for bi-directional shift register

* Data is shifted at the falling edge of the clock pulse.

Input pin for selecting the shift direction of bi-directional shift register

Data is shifted from Y160 to Y1 when set to LGND level "L", and data is shifted from Y1 to

Y160 when set to VDD level "H".

Refer to section 6.2.2.

Control input pin for output of non-select level

The input signal is level-shifted from logic voltage level to LCD drive voltage level, and

controls the LCD drive circuit.

When set to LGND level "L", the LCD drive output pins (Y1-Y160) are set to level Vss.

When set to "L”, the contents of the shift register are reset to not reading data. When

the /DISPOFF function is canceled, the driver outputs non-select level (V12 or V43), and

the shift data is read at the next falling edge of the LP. At that time, if /DISPOFF

removal time does not correspond to what is shown in AC characteristics, the shift data

is not read correctly.

Table of truth-values is shown in "TRUTH TABLE" in Functional Operations.

AC signal input pin for LCD drive waveform

The input signal is level-shifted from logic voltage level to LCD drive voltage level, and

controls the LCD drive circuit.

Normally it inputs a frame inversion signal.

The LCD drive output pins' output voltage levels can be set using the shift register

output signal and the FR signal.

Table of truth-values is shown in "TRUTH TABLE" in Functional Operations.

Preliminary Ver 0.24

Page 7/26

2009/10/01

Share Link: