SY100EP32V 데이터 시트보기 (PDF) - Micrel
부품명
상세내역
제조사
SY100EP32V Datasheet PDF : 9 Pages
| |||
Micrel, Inc.
ABSOLUTE MAXIMUM RATINGS(1)
Precision Edge®
SY10EP32V
SY100EP32V
Symbol
Rating
Value
Unit
VCC — VEE
VIN
IOUT
IBB
TA
TSTORE
TLEAD
θJA
Power Supply Voltage
Input Voltage (VCC = 0V, VIN not more negative than VEE)
Input Voltage (VEE = 0V, VIN not more positive than VCC)
Output Current
–Continuous
–Surge
VBB Sink/Source Current(2)
Operating Temperature Range
Storage Temperature Range
Lead Temperature (soldering, 20 sec.)
Package Thermal Resistance
(Junction-to-Ambient)
–Still Air SOIC
–Still Air MSOP
–multi-layer PCB
+6.0
–6.0 to 0
+6.0 to 0
50
100
±0.5
–40 to +85
–65 to +150
+260
160
206
V
V
V
mA
mA
°C
°C
°C
°C/W
°C/W
θJC
Package Thermal Resistance
(Junction-to-Case)
SOIC
39
MSOP
39
°C/W
°C/W
Note 1.
Note 2.
Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not
implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratlng conditions
for extended periods may affect device reliability.
Due to the limited drive capability, the VBB reference should only be used for inputs from the same packge device (i.e., do not sue for other
devices).
(10EP) LVPECL DC ELECTRICAL CHARACTERISTICS(1)
VCC = 3.3V ±10%; VEE = 0V(2)
TA = –40°C
TA = +25°C
TA = +85°C
Symbol
Parameter
Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit
IEE
Power Supply Current
VOH
Output HIGH Voltage(3)
VOL
Output LOW Voltage(3)
VIH
Input HIGH Voltage
(Single-Ended)
—
30
37
—
30
37
—
30
37
mA
2165 2290 2415 2230 2355 2480 2290 2415 2540 mV
1365 1490 1615 1430 1555 1680 1490 1615 1740 mV
2090 — 2415 2155 — 2480 2215 — 2540 mV
VIL
Input LOW Voltage
(Single-Ended)
1365 — 1690 1430 — 1755 1490 — 1815 mV
VBB
VIHCMR
Output Voltage
Input HIGH Voltage(4)
Common Mode Range
(Differential)
1790 1890 1990 1855 1955 2055 1915 2015 2115 mV
2.0
—
VCC
2.0
—
VCC
2.0
—
VCC
V
IIH
Input HIGH Current
—
—
150
—
—
150
—
—
150
µA
IIL
Input LOW Current
CLK 0.5
—
—
0.5
—
—
0.5
—
—
µA
/CLK –150 —
— –150 —
— –150 —
—
Note 1.
Note 2.
Note 3.
Note 4.
10EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit
is in a test socket or mounted on a printed circuit board and traverse airflow greater than 500lfpm is maintained.
Input and output parameters vary 1:1 with VCC.
All loading with 50Ω to VCC –2.0V.
The VIHCMR range is referenced to the most positive side of the differential input signal.
M9999-111605
hbwhelp@micrel.com or (408) 955-1690
3
Share Link: 