MC100EP33(2002) 데이터 시트보기 (PDF) - ON Semiconductor
부품명
상세내역
제조사
MC100EP33 Datasheet PDF : 12 Pages
| |||
MC10EP33, MC100EP33
MAXIMUM RATINGS (Note 2)
Symbol
Parameter
Condition 1
Condition 2
VCC
PECL Mode Power Supply
VEE
NECL Mode Power Supply
VI
PECL Mode Input Voltage
NECL Mode Input Voltage
Iout
Output Current
VEE = 0 V
VCC = 0 V
VEE = 0 V
VCC = 0 V
Continuous
Surge
VI VCC
VI VEE
IBB
VBB Sink/Source
TA
Operating Temperature Range
Tstg
Storage Temperature Range
qJA
Thermal Resistance (Junction–to–Ambient) 0 LFPM
500 LFPM
8 SOIC
8 SOIC
qJC
Thermal Resistance (Junction–to–Case)
std bd
qJA
Thermal Resistance (Junction–to–Ambient) 0 LFPM
500 LFPM
8 SOIC
8 TSSOP
8 TSSOP
qJC
Thermal Resistance (Junction–to–Case)
std bd
Tsol
Wave Solder
<2 to 3 sec @ 248°C
2. Maximum Ratings are those values beyond which device damage may occur.
8 TSSOP
Rating
6
–6
6
–6
50
100
± 0.5
–40 to +85
–65 to +150
190
130
41 to 44
185
140
41 to 44
265
Units
V
V
V
V
mA
mA
mA
°C
°C
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C
10EP DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 3)
–40°C
25°C
85°C
Symbol
IEE
VOH
VOL
VIH
VIL
VBB
VIHCMR
Characteristic
Power Supply Current
Output HIGH Voltage (Note 4)
Output LOW Voltage (Note 4)
Input HIGH Voltage (Single–Ended)
Input LOW Voltage (Single–Ended)
Output Voltage Reference
Input HIGH Voltage Common Mode
Range (Differential) (Note 5)
Min Typ Max Min Typ Max Min Typ Max Unit
18
26
34
18
26
34
18
26
34 mA
2165 2290 2415 2230 2355 2480 2290 2415 2540 mV
1365 1490 1615 1430 1555 1680 1490 1615 1740 mV
2090
2415 2155
2480 2215
2540 mV
1365
1690 1430
1755 1490
1815 mV
1790 1890 1990 1855 1955 2055 1915 2015 2115 mV
2.0
3.3 2.0
3.3 2.0
3.3
V
IIH
Input HIGH Current
150
150
150 mA
IIL
Input LOW Current
0.5
0.5
0.5
mA
NOTE: EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500 lfpm is maintained.
3. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to –2.2 V.
4. All loading with 50 W to VCC–2.0 volts.
5. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
http://onsemi.com
3
Share Link: 