MC100EP33MNR4 데이터 시트보기 (PDF) - ON Semiconductor
부품명
상세내역
제조사
MC100EP33MNR4 Datasheet PDF : 11 Pages
| |||
MC10EP33, MC100EP33
Table 10. 100EP DC CHARACTERISTICS, NECL VCC = 0 V; VEE = −5.5 V to −3.0 V (Note 17)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VBB
VIHCMR
Power Supply Current
Output HIGH Voltage (Note 18)
Output LOW Voltage (Note 18)
Input HIGH Voltage (Single−Ended)
Input LOW Voltage (Single−Ended)
Output Voltage Reference
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 19)
18
26
40
23
26
45
23
26
45 mA
−1145 −1020 −895 −1145 −1020 −895 −1145 −1020 −895 mV
−1945 −1820 −1695 −1945 −1820 −1695 −1945 −1820 −1695 mV
−1225
−880 −1225
−880 −1225
−880 mV
−1945
−1625 −1945
−1625 −1945
−1625 mV
−1525 −1425 −1325 −1525 −1425 −1325 −1525 −1425 −1325 mV
VEE+2.0
0.0
VEE+2.0
0.0
VEE+2.0
0.0 V
IIH
Input HIGH Current
IIL
Input LOW Current
150
150
150 mA
0.5
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
17. Input and output parameters vary 1:1 with VCC.
18. All loading with 50 W to VCC − 2.0 V.
19. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
Table 11. AC CHARACTERISTICS VCC = 0 V; VEE = −3.0 V to −5.5 V or VCC = 3.0 V to 5.5 V; VEE = 0 V (Note 20)
−40°C
25°C
85°C
Symbol
Characteristic
Min
VOPP
Output Voltage Amplitude
(See Figure 3)
fin < 4.0 GHz
fin < 4.5 GHz
tPLH,
tPHL
Propagation Delay to
Output Differential
CLK/Q 300
RESET/Q 370
tRR
Set/Rest Recovery
150
tPW
Minimum Pulse width
RESET 550
tJITTER Random Clock Jitter (RMS)
VPP
Input Voltage Swing
150
(Differential Configuration)
Typ Max Min
700
600
380 440 300
420 470 370
100
200
480
550
0.2
2
800 1200 150
Typ Max Min
700
600
380 440 320
420 470 400
100
200
480
550
0.2
2
800 1200 150
Typ Max Unit
mV
700
600
400 460 ps
450 500
100
ps
480
ps
0.2
2
ps
800 1200 mV
tr
Output Rise/Fall Times
tf
(20% − 80%)
Q, Q 90 170 200 100 180 250 120 200 280 ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
20. Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 W to VCC − 2.0 V.
http://onsemi.com
6
Share Link: 