DatasheetQ Logo
Electronic component search and free download site. Transistors,MosFET ,Diode,Integrated circuits

MC33143DW 데이터 시트보기 (PDF) - Motorola => Freescale

부품명
상세내역
제조사
MC33143DW
Motorola
Motorola => Freescale Motorola
MC33143DW Datasheet PDF : 8 Pages
1 2 3 4 5 6 7 8
Freescale SMeCm33i1c4o3nductor, Inc.
DC ELECTRICAL CHARACTERISTICS (Characteristics noted under conditions 9.0 V VPwr 17 V, 4.5 V VDD 5.5 V,
–40°C TL 125°C, unless otherwise noted, typical values represent approximate mean at TL = 25°C.)
Characteristic
CONTROL INTERFACE
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Input Control
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Logic High (IO = –0.1 A) (Note 1)
Symbol
Min
Typ
Max
Unit
VDD
VIH
0.7
0.56
Logic Low (IO = 0) (Note 2)
Input Logic Voltage Hysteresis (VIH – VIL)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Input Pull–Down Current (0.3 x VDD Vin < 0.7 x VDD) (Note 3)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Chip–Enable Threshold
VIL
Vhys
Iin(pd)
0.52
0.3
50
250
500
mV
20
44
100
µA
VDD
Logic Low (Note 4)
Logic High (Note 5)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Chip–Enable Hysteresis (VCEN(IH) – VCEN(IL))
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Chip–Enable Pull–Up Current (CEN = 0.7 x VDD)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Status Low Voltage (Iin = 600 µA) (Note 6)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Status Pull–Up Current (Note 7)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Interrupt (Note 8)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Logic High
VCEN(IL)
VCEN(IH)
0.7
VCEN(hys)
50
ICEN(pu)
–2.0
VSTAT(low)
ISTAT(pu)
–20
INTh
0.7
0.5
0.5
150
–16.8
0.07
–44
0.3
500
–40
0.2
–100
mV
µA
VDD
µA
VDD
Logic Low
INTl
0.3
NOTES: 1. Upper logic threshold voltage applies to IN1, IN2, and SFPD and expressed in VDD units
2. Lower logic threshold voltage applies to IN1, IN2, and SFPD and expressed in VDD units.
3. Applies to IN1, IN2, and SFPD.
4. Initially have CEN = 0.7 x VDD, Ramp CEN down from VDD until IO = 0 and note disabling point.
5. Initially have Vin = 0.7 x VDD, Ramp CEN up from ground until IO = 0.1 A and note enabling point.
6. Applies equally to STAT1–2 and INT outputs; Measured threshold voltage by applying an “open” fault to OUT1 or OUT2 while forcing 600 µA of
current into STAT1–2 or INT.
7. Measured with no faults on OUT1–2, VSTAT = VINT = 0.8 x VDD.
8. The Interrupt output has an internal active current pull–up.
DC ELECTRICAL CHARACTERISTICS (Characteristics noted under conditions 9.0 V VPwr 17 V, 4.5 V VDD 5.5 V,
–40°C TL 125°C, unless otherwise noted, typical values represent approximate mean at TL = 25°C.)
Characteristic
Symbol
Min
Typ
Max
Unit
OUTPUT DYNAMICS
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Output Short Sense Time (Note 1)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Output Short Refresh Time (Note 2)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Output Open Sense ON Time (Note 3)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Output Propagation Delay
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Turn–On (Output Low to High) (Note 4)
Turn–Off (Output High to Low) (Note 5)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Output Slew Rate
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Output Rising (Note 6)
tss
30
54
100
µs
tref
3.0
4.1
6.0
ms
tos(on)
3.0
6.4
12
ms
µs
tdlh
7.2
50
tdhl
40
75
V/µs
SRr
0.2
11
10
Output Falling (Note 7)
SRf
0.2
2.6
10
NOTES: 1. CEN = 0.7 x VDD, SFPD = 0.3 x VDD, RL = 0, Step Vin from 0.3 x VDD to 0.7 x VDD; Sense time measured from step until STAT = 0.2 x VDD.
2. CEN = IN1 = IN2 = 0.7 x VDD, RL = 0; Refresh time measured from output disable until output is re–enabled.
3. RL = “open”, Step Vin from ground to 0.7 x VDD, Open sense time measured from step until VSTAT 0.2 x VDD.
4. RL = 12 , CL = 0.01 µF, step Vin from VIL to VIH; Turn–On propagation measured from Vin = 0.5 x VDD until Vout = 2.0 V (see Figure 2).
5. RL = 12 , CL = 0.01 µF, step Vin from VIH to VIL; Turn–Off propagation measured from Vout = VPwr –3.0 V until Vout = 2.0 V (see Figure 2).
6. RL = 12 , CL = 0.01 µF, step Vin from VIL to VIH; Output Slew Rate measured from 2.0 V to VPwr – 3.0 V (see Figure 2).
7. RL = 12 , CL = 0.01 µF, step Vin from VIH to VIL; Output Slew Rate measured from VPwr – 3.0 V to 2.0 V (see Figure 2).
4
MOTOROLA ANALOG IC DEVICE DATA
For More Information On This Product,
Go to: www.freescale.com

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]