MC68160AFB 데이터 시트보기 (PDF) - Motorola => Freescale

부품명

상세내역

제조사

MC68160AFB

ENHANCED ETHERNET INTERFACE TRANSCEIVER

Motorola => Freescale 

MC68160A

Table 1. Pin Function Description (continued)

Pin(s)

Symbol

Type

Name/Function

OSCILLATOR AND FREQUENCY MULTIPLIER

12

MFILT

C

Frequency Multiplier Filter Connection Point: An external resistor capacitor filter must be

attached to this pin.

16

X1

I/C

Oscillator Inverter Input and Crystal Connection Point: When connected for crystal

CMOS oscillator operation, the frequency of the clock which appears at TCLK is half that of the

crystal oscillator. As an option, instead of connecting to a crystal, X1 may be driven from an

external 20 MHz CMOS compatible clock generator.

17

X2

O/C

Oscillator Inverter Output and Crystal Connection Point: This pin is used only for the

CMOS connection of an external crystal and capacitor. It must be left unconnected if X1 is driven by

an external CMOS Clock generator.

MODE SELECT

3

CS0

4

CS1

5

CS2

6

LOOP

9

APORT

27

TPSQEL

28

TPFULDL

29

TPAPCE

46

TPEN

I

Mode Select: The logic states applied to these pins select the appropriate interface for the

TTL

desired IEEE–802.3 controller or enable the standby mode. When the standby mode is

selected, the MC68160A power supply current is greatly reduced. Additionally, in the standby

mode, all of the controller inputs and outputs are driven to the high impedance state.

I

Diagnostic Loopback: Asserting this function causes serial NRZ data at the TX input to be

TTL

Manchester encoded and then looped back through the Manchester decoder, appearing at

the RX output. This diagnostic loopback function operates independent of Twisted Pair (TP)

or Access Unit Interface (AUI) port connectivity or activity. Neither the TP port nor the AUI

port transmits data from the controller while diagnostic loopback is selected. Likewise, the

controller interface receives data neither from the TP nor the AUI receivers while in this

mode. The polarity fault detection and link integrity functions are not inhibited by the

diagnostic loopback mode. If otherwise enabled, they continue to function. If the twisted pair

port is selected, and TPSQEL is driven to the low logic state, a collision detect pulse is

delivered following each transmission to simulate the twisted pair SQE test.

I

Automatic Port Selection Enable: When high, MC68160A will automatically select the TP

TTL

or AUI port based on the presence or absence of valid link beats or frames at the TP receive

input. If the AUI port is automatically selected, the MC68160A will continue to produce link

pulses for the TP port. Changing ports requires approximately 1.0 ms to allow the circuitry for

the new port to resume normal operation. The power consumption is minimized in the

circuitry associated with the unselected port.

I

Twisted Pair Signal Quality Error Test Enable: Forcing this pin low enables testing of the

TTL

internal TP collision detect circuitry after each transmit operation to the TP media. This

function provides a simulated collision to as much of the MC68160A collision detect circuitry

as possible without affecting the attached twisted pair channel. A normal SQE test results in

a high logic state at the CLSN controller interface pin which begins 6 to 16–bit times after the

last transition of a transmitted signal and continues for 5 to 15–bit times. (When the AUI port

is selected, SQE test signals are generated by the coaxial cable transceiver and delivered to

the controller via the MC68160A ACX+/– receive inputs)

I

Twisted Pair Full Duplex Mode Select: Forcing this pin low allows simultaneous transmit

TTL

and receive operation on the twisted pair port without an indicated collision. This pin is not to

be asserted with LOOP as a test mode is enabled that disrupts normal operation.

I

Twisted Pair Automatic Polarity Correction Enable: When TPAPCE is high, automatic

TTL

polarity correction is enabled, and MC68160A will internally correct for a polarity fault on the

receive circuit. Additionally, when TPAPCE is high, the presence of a polarity fault is

indicated on TPPLR.

I/O

Twisted Pair Port Enable: If APORT is low, TPEN is an input which determines whether the

TTL

AUI port (TPEN low) or TP port (TPEN high) will be manually selected. If the AUI port is

(TTL/CMOS) manually selected, the MC68160A will not produce link pulses for the TP port.

If APORT is high, TPEN is an output which will indicate which port has been automatically

selected by driving TPEN low (for AUI) or high (for TP). In its output mode TPEN can sink

10 mA in the low output state and source 10 mA in the high output state. (See Pin 9

Description.)

Changing ports requires approximately 1.0 ms to allow the circuitry for the new port to

resume normal operation. The power consumption is minimized in the circuitry associated

with the unselected port. In the standby mode, this pin is driven to the high impedance state.

MOTOROLA ANALOG IC DEVICE DATA

5

Share Link: