DS1202N 데이터 시트보기 (PDF) - Dallas Semiconductor -> Maxim Integrated

부품명

상세내역

제조사

DS1202N

Serial Timekeeping Chip

Dallas Semiconductor -> Maxim Integrated 

DS1202, DS1202S

RESET AND CLOCK CONTROL

All data transfers are initiated by driving the RST input

high. The RST input serves two functions. First, RST

turns on the control logic which allows access to the shift

register for the address/command sequence. Second,

the RST signal provides a method of terminating either

single byte or multiple byte data transfer. A clock cycle is

a sequence of a falling edge followed by a rising edge.

For data inputs, data must be valid during the rising

edge of the clock and data bits are output on t he falling

edge of clock. All data transfer terminates if the RST in-

put is low and the I/O pin goes to a high impedance

state. Data transfer is illustrated in Figure 3.

DATA INPUT

Following the eight SCLK cycles that input a write com-

mand byte, a data byte is input on the rising edge of the

next eight SCLK cycles. Additional SCLK cycles are ig-

nored should they inadvertently occur. Data is input

starting with bit 0. Due to the inherent nature of the logic

state machine, writing times containing an absolute

value of “59” seconds should be avoided.

DATA OUTPUT

Following the eight SCLK cycles that input a read com-

mand byte, a data byte is output on the falling edge of

the next eight SCLK cycles. Note that the first data bit to

be transmitted occurs on the first falling edge after the

last bit of the command byte is written. Additional SCLK

cycles retransmit the data bytes should they inadver-

tently occur so long as RST remains high. This opera-

tion permits continuous burst mode read capability.

Data is output starting with bit 0.

BURST MODE

Burst mode may be specified for either the clock/calen-

dar or the RAM registers by addressing location 31 deci-

mal (address/command bits one through five = logical

one). As before, bit six specified clock or RAM and bit 0

specifies read or write. There is no data storage capac-

ity at locations 8 through 31 in the Clock/Calendar Reg-

isters or locations 24 through 31 in the RAM registers.

When writing to the clock registers in the burst mode,

the first eight registers must be written in order for the

data to be transferred.

However, when writing to RAM in burst mode it is not

necessary to write all 24 bytes for the data to transfer.

Each byte that is written to will be transferred to RAM

regardless of whether all 24 bytes are written or not.

CLOCK/CALENDAR

The clock/calendar is contained in eight write/read reg-

isters as shown in Figure 4. Data contained in the clock/

calendar registers is in binary coded decimal format

(BCD).

CLOCK HALT FLAG

Bit 7 of the seconds register is defined as the clock halt

flag. When this bit is set to logic 1, the clock oscillator is

stopped and the DS1202 is placed into a low–power

standby mode with a current drain of not more than 100

nanoamps. When this bit is written to logic 0, the clock

will start.

AM–PM/12–24 MODE

Bit 7 of the hours register is defined as the 12– or

24–hour mode select bit. When high, the 12–hour mode

is selected. In the 12–hour mode, bit 5 is the AM/PM bit

with logic high being PM. In the 24–hour mode, bit 5 is

the second 10 hour bit (20–23 hours).

WRITE PROTECT BIT

Bit 7 of the control register is the write protect bit. The

first seven bits (bits 0–6) are forced to zero and will al-

ways read a zero when read. Before any write operation

to the clock or RAM, bit 7 must be zero. When high, the

write protect bit prevents a write operation to any other

register.

CLOCK/CALENDAR BURST MODE

The clock/calendar command byte specifies burst

mode operation. In this mode the eight clock/calendar

registers can be consecutively read or written (see Fig-

ure 4) starting with bit 0 of address 0.

RAM

The static RAM is 24 x 8 bytes addressed consecutively

in the RAM address space.

RAM BURST MODE

The RAM command byte specifies burst mode opera-

tion. In this mode, the 24 RAM registers can be consec-

utively read or written (see Figure 4) starting with bit 0 of

address 0.

032697 3/11

Share Link: