STLC5048 데이터 시트보기 (PDF) - STMicroelectronics

부품명

상세내역

제조사

STLC5048

FULLY PROGRAMMABLE FOUR CHANNEL CODEC AND FILTER

STMicroelectronics 

STLC5048

In the multiple byte instructions the first one specifies the command or the register address and the access type

(Read or Write).

The following bytes contain the data to be loaded into the internal RAM (on CI wire) or carry out the RAM content

(on CO wire) depending on the R/W bit of the first byte. CO wire is normally in High Impedance and goes to low

impedance only after the first byte in case of Read operation. This allows to use a common wire for both CI/CO.

CS, normally High, is set Low during the transmission/reception of a byte, lasting 8 CCLK pulses. Between two

consecutive access the CS must be set high.

The CCLK can be a continuos or a gated clock.

The result of any instruction (read/write operation), if negative, can generate an interrupt (maskable). The inter-

rupt register (INT) contains the cause information of the generated interrupt and it is cleared every time that it

is read.

Depending on the instruction specified in the first byte, the STLC5048 waits a defined number of data bytes. If

the STLC5048 doesn't receive the data byte within a predefined period specified by means of T_OUT command,

an internal time out rejects the instruction. The time-out time is verified between two consecutive MCU interface

access (between the falling edge of the CS and the following rising edge).

This feature is used to verify the synchronisation of the MCU interface: however it can be disabled if not desired

(see T_OUT reg description). To check this synchronisation is provided a specific register (SYNCK) that returns

always a predefined value: if the returned value is different the MCU interface is in out of sync state (the device

is waiting a data byte while the MCU is writing an address or vice versa). In this case, it is possible to realign it

by means of the execution of a specific single byte instruction (REACOM) from 1 to 53 times, depending on the

instructions.

Every time an illegal operation (access to not allowed address, time-out violation or clock pulse different than 8

inside a CS active) is performed the MCU interface is put on an error state: to resume it from this state a single

REACOM instruction can be used.

Anyway after a REACOM instruction a successful SYNC instruction guarantees the correct synchronisation.

One additional wire provided to the control interface is an open drain interrupt output (INT) that goes low when

a change of status is detected on the I/O pins or other interrupt source are active (see INT register). INT is au-

tomatically reset after reading of the register corresponding the cause that has generated the interrupt (see INT

register description).

A particular register (COMEN) allows to enable a command on different channel at the same time. Every time

a command operation is performed at least one channel must be enabled in this register.

This feature is useful when all channels must be configured in the same condition. When a command is used

to perform a read operation only one channel can be enabled at the same time.

To check the configuration of the device a checksum value is provided. This value is calculated on all coefficient

parameters entered (coefficients of KD, AFE_CFF, GRX, GTX, RFC, XFC, BFC, ZFC blocks; see CKSUM reg-

ister description). Two commands are required to get this value: the first one (CKSTART) starts the internal

checksum calculation, the second one (CKSUM) returns the calculated value. Between this two commands no

other operation are allowed. The checksum value is available within 400us the CKSTART command.

Coefficient checksum is defined by this algorithm:

X16 + X12 + X5 + 1

This algorithm guarantees a fault coverage of 1 - 2-16.

PROGRAMMING THE DEVICE

After the power up, the filters and gain blocks can be programmed also with all the channels set in Power Down.

In this case the PDR bit of the COMEN register must be set to 0.

With the proper setting of the COMEN register, the commands can be applied to more than one channel at the

same time.

To read the coefficient values loaded in the RAM, only one channel per time must be enabled in the COMEN

register.

11/45

Share Link: