MC10EP08DR2G(2016) 데이터 시트보기 (PDF) - ON Semiconductor
부품명
상세내역
제조사
MC10EP08DR2G Datasheet PDF : 10 Pages
| |||
MC10EP08, MC100EP08
Table 10. 100EP DC CHARACTERISTICS, NECL (VCC = 0 V; VEE = −5.5 V to −3.0 V (Note 1))
−40°C
25°C
85°C
Symbol
IEE
VOH
VOL
VIH
VIL
VIHCMR
Characteristic
Power Supply Current
Output HIGH Voltage (Note 2)
Output LOW Voltage (Note 2)
Input HIGH Voltage (Single-Ended)
Input LOW Voltage (Single-Ended)
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 3)
Min Typ Max Min Typ Max Min Typ Max Unit
20
28
36
20
30
38
20
32
40 mA
−1145 −1020 −895 −1145 −1020 −895 −1145 −1020 −895 mV
−1945 −1820 −1695 −1945 −1820 −1695 −1945 −1820 −1695 mV
−1225
−880 −1225
−880 −1225
−880 mV
−1945
−1625 −1945
−1625 −1945
−1625 mV
VEE + 2.0
0.0
VEE + 2.0
0.0
VEE + 2.0
0.0
V
IIH
Input HIGH Current
IIL
Input LOW Current
D
D
0.5
−150
150
0.5
−150
150
0.5
−150
150 mA
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC.
2. All loading with 50 W to VCC − 2.0 V.
3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
Table 11. AC CHARACTERISTICS (VCC = 0 V; VEE = −3.0 V to −5.5 V or VCC = 3.0 V to 5.5 V; VEE = 0 V (Note 1))
−40°C
25°C
85°C
Symbol
fmax
tPLH,
tPHL
Characteristic
Maximum Frequency (Figure 2)
Propagation Delay to
Output Differential
D, D to Q, Q
Min Typ Max Min Typ Max Min Typ Max Unit
>3
>3
>3
GHz
ps
170 220 280 180 250 300 200 270 320
tJITTER
VPP
Cycle-to-Cycle Jitter (Figure 2)
Input Voltage Swing
(Differential Configuration)
0.2 < 1
0.2 < 1
0.2 < 1 ps
150 800 1200 150 800 1200 150 800 1200 mV
tr
Output Rise/Fall Times
tf
Q, Q (20%−80%)
ps
70 120 170 80 130 180 100 150 200
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 W to VCC − 2.0 V.
www.onsemi.com
6
Share Link: 