DatasheetQ Logo
Electronic component search and free download site. Transistors,MosFET ,Diode,Integrated circuits

PCA82C250 데이터 시트보기 (PDF) - NXP Semiconductors.

부품명
상세내역
제조사
PCA82C250
NXP
NXP Semiconductors. NXP
PCA82C250 Datasheet PDF : 18 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
NXP Semiconductors
PCA82C250
CAN controller interface
10. Thermal characteristics
Table 7.
Symbol
Rth(j-a)
Thermal characteristics
Parameter
thermal resistance from junction to ambient
Conditions
in free air
Typ
Unit
160
K/W
11. Characteristics
Table 8. Characteristics
VCC = 4.5 to 5.5 V; Tamb = 40 to +125 C; RL = 60 ; I8 > 10 A; unless otherwise specified; all voltages referenced to
ground (pin 2); positive input current; all parameters are guaranteed over the ambient temperature range by design, but only
100 % tested at +25 C.
Symbol Parameter
Conditions
Min
Typ Max
Unit
Supply
I3
supply current
DC bus transmitter
dominant; V1 = 1 V
recessive; V1 = 4 V; R8 = 47 k
recessive; V1 = 4 V; V8 = 1 V
Standby; Tamb < 90 C
-
-
-
[1] -
-
70
mA
-
14
mA
-
18
mA
100 170
A
VIH
HIGH-level input voltage
output recessive
0.7VCC -
VCC + 0.3 V
VIL
LOW-level input voltage
output dominant
0.3 -
0.3VCC V
IIH
HIGH-level input current
V1 = 4 V
200 -
+30
A
IIL
LOW-level input current
V1 = 1 V
100 -
600
A
V6,7
recessive bus voltage
V1 = 4 V; no load
2.0
-
3.0
V
ILO
off-state output leakage current 2 V < (V6,V7) < 7 V
2
-
+1
mA
5 V < (V6,V7) < 18 V
5
-
+12
mA
V7
CANH output voltage
V1 = 1 V
2.75 -
4.5
V
V6
CANL output voltage
V1 = 1 V
0.5
-
2.25
V
V6, 7
difference between output
voltage at pins 6 and 7
V1 = 1 V
V1 = 1 V; RL = 45 ; VCC 4.9 V
1.5
-
3.0
V
1.5
-
-
V
V1 = 4 V; no load
500 -
+50
mV
Isc7
short-circuit CANH current
V7 = 5 V; VCC 5 V
-
-
105
mA
V7 = 5 V; VCC = 5.5 V
-
-
120
mA
Isc6
short-circuit CANL current
V6 = 18 V
-
-
160
mA
DC bus receiver: V1 = 4 V; pins 6 and 7 externally driven; 2 V < (V6, V7) < 7 V; unless otherwise specified
Vdiff(r)
differential input voltage
(recessive)
7 V < (V6, V7) < 12 V;
not Standby mode
1.0 -
+0.5
V
1.0 -
+0.4
V
Vdiff(d)
differential input voltage
(dominant)
7 V < (V6, V7) < 12 V;
not Standby mode
0.9
-
5.0
V
1.0
-
5.0
V
Vdiff(hys) differential input hysteresis
VOH
HIGH-level output voltage
see Figure 5
pin 4; I4 = 100 A
-
150 -
mV
0.8VCC -
VCC
V
PCA89C250
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 06 — 25 August 2011
© NXP B.V. 2011. All rights reserved.
5 of 18

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]