SPT7610SIQ 데이터 시트보기 (PDF) - Cadeka Microcircuits LLC.

부품명

상세내역

제조사

SPT7610SIQ

6-BIT, 1 GSPS FLASH A/D CONVERTER

Cadeka Microcircuits LLC. 

Figure 3 – Typical Interface Circuit

VIN**

50 W

VIN

VIN

VRTF

DRB

DRB

DRA

DRA

R

R

–2.0 V

Reference

*

+

22 W

–U1

*

*

–

22 W 2N2907

+U1

*

VRTS

VR3

VRM

VR1 SPT7610

VRBS

VRBF

–5.2 V

–5.2 V

Convert

U2

50 W

50 W

CLK

NCLK

MINV

LINV

Test

–2 V

Pulldown

(Analog)

* FB

–5.2 V

DRB (DATA READY)

DRB (DATA READY)

DRA (DATA READY)

DRA (DATA READY)

D6B (OVR)

D5B (MSB)

D4B

D3B

D2B

D1B

D0B (LSB)

D6A (OVR)

D5A (MSB)

D4A

D3A

D2A

D1A

D0A (LSB)

–5.2 V

–5.2 V

–5.2 V

.1 µF

–2.0 V

Pulldown

(Digital)

FB = Ferrite bead

U1 = TLV2464 or equivalent with low offset/noise.

R = 1 kW; 0.05% matched or better

= AGND

= DGND

U2 = Motorola ECLinPS Lite, MC10EL16, differential receiver.

* = 2.2 µF Tantalum Capacitor, 0.1 µF and 100 pF chip capacitors.

** = Care must be taken to avoid exceeding the maximum rating

for the input, especially during power up sequencing of the

analog input driver.

TYPICAL INTERFACE CIRCUIT

The typical interface circuit is shown in figure 3. External

reference taps are provided for correcting integral

nonlinearity errors. These taps can be actively driven to

reduce these errors. (See the Reference Inputs discus-

sion below.) The SPT7610 evaluation board application

note contains more details on interfacing the SPT7610.

The function of each pin and external connections to other

components is as follows:

POWER SUPPLY PINS: AVEE, AGND, DGND

AVEE is the supply pin with AGND as ground for the de-

vice. The AVEE power supply pin should be bypassed as

close to the device as possible with a 10 µF tantalum ca-

pacitor, in parallel with 100 pF and .01 µF chip capacitors.

Place the 100 pF chip capacitor closest to the SPT7610.

Digital ground (DGND) is the ground for the ECL outputs

and is to be referenced to the output pulldown voltage and

appropriately bypassed as shown in figure 3.

ANALOG INPUT: VIN

There are two analog input pins that are tied to the same

point internally. Either one may be used as an analog input

sense and the other for input force. This is convenient for

testing the source signal to see if there is sufficient drive

capability. The pins can also be tied together and driven by

the same source. The SPT7610 is superior to similar de-

vices due to a preamplifier stage before the comparators.

This makes the device easier to drive because it has con-

stant capacitance and induces less slew rate distortion.

CLOCK INPUTS: CLK, NCLK

The clock inputs are designed to be driven differentially

with ECL levels. The duty cycle of the clock should be kept

at 50% to avoid causing larger second harmonics. If this is

not important to the intended application, then duty cycles

other than 50% may be used.

SPT7610

6

1/21/02

Share Link: