5962-9207807HTX 데이터 시트보기 (PDF) - White Electronic Designs Corporation
부품명
상세내역
제조사
5962-9207807HTX Datasheet PDF : 6 Pages
| |||
White Electronic Designs
WS512K8-XCX
ABSOLUTE MAXIMUM RATINGS
TRUTH TABLE
Parameter
Symbol Min Max Unit
Operating Temperature
TA
-55 +125 °C
Storage Temperature
TSTG
-65
+150
°C
Signal Voltage Relative to GND VG
-0.5 VCC+0.5 V
Junction Temperature
TJ
150
°C
Supply Voltage
VCC
-0.5
7.0
V
RECOMMENDED OPERATING CONDITIONS
Parameter
Supply Voltage
Input High Voltage
Input Low Voltage
Operating Temp. (Mil.)
Symbol
VCC
VIH
VIL
TA
Min Max Unit
4.5
5.5
V
2.2 VCC + 0.3 V
-0.5 +0.8
V
-55 +125 °C
CS# OE# WE#
Mode
H
X
X
Standby
L
L
H
Read
L
X
L
Write
L
H
H Out Disable
Data I/O
High Z
Data Out
Data In
High Z
Power
Standby
Active
Active
Active
CAPACITANCE
(TA = +25°C)
Parameter
Symbol
Condition
Max Unit
Input capacitance
CIN
VIN = 0V, f = 1.0MHZ
45
pF
Output capicitance COUT VOUT = 0V, f = 1.0MHZ 45
pF
This parameter is guaranteed by design but not tested.
DC CHARACTERISTICS
(VCC = 5.0V, GND = 0V, -55°C ≤ TA ≤ 125°C)
Parameter
Symbol Conditions
Input Leakage Current
ILI VCC = 5.5, VIN = GND to VCC
Output Leakage Current
ILO CS# = VIH, OE# = VIH, VOUT = GND to VCC
Operating Supply Current
ICC CS# = VIL, OE# = VIH, f = 5MHZ, VCC = 5.5
Standby Current
ISB CS# = VIH, OE# = VIH, f = 5MHZ
Output Low Voltage
VOL IOL = 8mA, VCC = 4.5
Output High Voltage
VOH IOH = -4.0mA, VCC = 4.5
NOTE: DC test conditions: VIH = VCC -0.3V, VIL = 0.3V
-20
Min Max
10
10
210
80
0.4
2.4
-25
Min Max
10
10
210
60
0.4
2.4
-35
Min Max
10
10
210
60
0.4
2.4
-45
Min Max
10
10
210
55
0.4
2.4
Units
µA
µA
mA
mA
V
V
DATA RETENTION CHARACTERISTICS FOR LOW POWER “L” VERSION
(-55°C ≤ TA ≤ 125°C)
Parameter
Symbol Conditions
Data Retention Supply Voltage VDR CS# • VCC -0.2V
Data Retention Current
ICCDR1 VCC = 3V
-20
-25
-35
-45
Units
Min Typ Max Min Typ Max Min Typ Max Min Typ Max
2.0
5.5 2.0
5.5 2.0
5.5 2.0
5.5 V
8.0 12.8
8.0 12.8
8.0 12.8
8.0 12.8 mA
FIGURE 2 – AC TEST CIRCUIT
IOL
Current Source
D.U.T.
CEFF = 50 pf
VZ 1.5V
(Bipolar Supply)
IOH
Current Source
AC TEST CONDITIONS
Parameter
Typ
Unit
Input Pulse Levels
VIL = 0, VIH = 3.0 V
Input Rise and Fall
5
ns
Input and Output Reference Level
1.5
V
Output Timing Reference Level
1.5
V
NOTES:
VZ is programmable from -2V to +7V.
IOL & IOH programmable from 0 to 16mA.
Tester Impedance Z0 = 75 Ω
VZ is typically the midpoint of VOH and VOL.
IOL & IOH are adjusted to simulate a typical resistive load circuit.
ATE tester includes jig capacitance.
May 2004
Rev. 4
2
White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com
Share Link: 