PI3B16248 데이터 시트보기 (PDF) - Pericom Semiconductor Corporation

부품명

상세내역

제조사

PI3B16248

3.3V, 24-Bit to 48-Bit Mux/DeMux NanoSwitch™

Pericom Semiconductor Corporation 

PI3B16248

3.3V, 24-Bit to 48-Bit,

Mux/DeMux NanoSwitch™

Maximum Ratings

(Above which useful life may be impaired. For user guidelines, not tested.)

Storage Temperature ........................................................ –65°C to +150°C

Ambient Temperature with Power Applied ....................... –40°C to +85°C

Supply Voltage Range......................................................... –0.5V to +4.6V

DC Input Voltage ................................................................ –0.5V to +4.6V

DC Output Current............................................................................120mA

Power Dissipation ................................................................................0.5W

Note:

Stresses greater than those listed under MAXIMUM

RATINGS may cause permanent damage to the device. This

is a stress rating only and functional operation of the device

at these or any other conditions above those indicated in the

operational sections of this specification is not implied. Ex-

posure to absolute maximum rating conditions for extended

periods may affect reliability.

DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 3.0 to 3.6V)

Parameters

Description

Test Conditions(1)

Min. Typ.(2)

VIH

Input HIGH Voltage

S1, S2

2.0

VIL

Input LOW Voltage

S1, S2

-0.5

IIH

Input HIGH Current

VCC = MAX., VIN = VCC

IIL

Input LOW Current

VCC - MAX., VIN = GND

RON

Switch On-Resistance

VCC = Min., VIN = 0V, ION = 24mA

5

VCC = Min., VIN = 0V, ION = 12mA

10

CIN

Input Capacitance

VCC = 0V, 25°C, f = 1 MHz

CON

Output Capacitance

VCC = 0V, 25°C, f = 1 MHz

ICC

IOZH

VIK

Power Supple Quiescent

High Impedance Output Current

Clamp Diode Voltage

VCC = Max., VIN = GND or VCC

0 ≤ A, B ≤ VCC

VCC = Min., IIN = -18mA

`

-0.7

Note:

1. Typical values are shown at VCC = 3.3V, +25°C ambient and maximum loading.

Max.

0.8

±1

±1

8

15

3.0

25.0

20

±1

-1.2

Units

V

µA

Ω

pF

µA

V

Electrical Characteristics (VCC = 3.0V to 3.6V, TA = –40°C to +85°C)

Parameters

Description

Test Conditions

Com.

Min.

Max.

Units

tPLH

tEN(3)

tDIS(3)

tM

Propagation Delay AX to BX

Bus Enable

Bus Disable

Make-before-break time

CL = 50pF, RL = 500Ω

CL = 50pF

1

RL = 500Ω

1

R = 500Ω

0

250

ps

4.5

5.0

ns

2

Notes:

1. This parameter is guaranteed but not tested on Propagation Delays.

2. The bus switch contributes no propagational delay other than the RC delay of the On-Resistance of the switch and the load capacitance. The

time constant for the switch alone is of the order of 0.25ns for 50pF load. Since this time constant is much smaller than the rise/fall times of

typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is

determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side.

3. See test circuit and waveforms.

3

PS8172E

09/10/04

Share Link: