SI3018-F-FM 데이터 시트보기 (PDF) - Silicon Laboratories

부품명

상세내역

제조사

SI3018-F-FM

PROGRAMMABLE VOICE DAA SOLUTIONS

Silicon Laboratories 

Si3050 + Si3011/18/19

Table 4. AC Characteristics

(VD = 3.0 to 3.6 V, TA = 0 to 70 °C, Fs = 8000 Hz, see "2. Typical Application Schematic" on page 17)

Parameter

Symbol

Test Condition

Min Typ Max Unit

Sample Rate

Fs

8

— 16 kHz

PCLK Input Frequency

PCLK

256 — 8192 kHz

Receive Frequency Response

Low –3 dBFS Corner, FILT = 0 —

5

—

Hz

Receive Frequency Response

Low –3 dBFS Corner, FILT = 1 — 200 —

Hz

Transmit Full-Scale Level1

VFS

FULL = 0 (0 dBm)

FULL = 1 (+3.2 dBm)2

FULL2 = 1 (+6.0 dBm)2

—

1.1

— VPEAK

—

1.58 — VPEAK

—

2.16 — VPEAK

Receive Full-Scale Level1,3

VFS

FULL = 0 (0 dBm)

FULL = 1 (+3.2 dBm)2

FULL2 = 1 (+6.0 dBm)2

—

1.1

— VPEAK

—

1.58 — VPEAK

—

2.16 — VPEAK

Dynamic Range4,5,6

DR ILIM = 0, DCV = 11, MINI=00 —

80 —

dB

DCR = 0, IL = 100 mA

Dynamic Range4,5,6

DR ILIM = 0, DCV = 00, MINI=11 —

80 —

dB

DCR = 0, IL = 20 mA

Dynamic Range4,5,6

DR ILIM = 1, DCV = 11, MINI=00 —

80 —

dB

DCR = 0, IL = 50 mA

Transmit Total Harmonic

Distortion6,7

THD ILIM = 0, DCV = 11, MINI=00 — –72 —

dB

DCR = 0, IL = 100 mA

Transmit Total Harmonic

Distortion6,7

THD ILIM = 0, DCV = 00, MINI=11 — –78 —

dB

DCR = 0, IL = 20 mA

Receive Total Harmonic

Distortion6,7

THD ILIM = 0, DCV = 00, MINI=11 — –78 —

dB

DCR = 0, IL = 20 mA

Receive Total Harmonic

Distortion6,7

THD ILIM = 1,DCV = 11, MINI=00 — –78 —

dB

DCR = 0, IL = 50 mA

Notes:

1. Measured at TIP and RING with 600 termination at 1 kHz, as shown in Figure 1 on page 6.

2. With FULL = 1, the transmit and receive full-scale level of +3.2 dBm can be achieved with a 600  ac termination.

While the transmit and receive level in dBm varies with reference impedance, the DAA will transmit and receive 1 dBV

into all reference impedances. With FULL2 = 1, the transmit and receive full-scale level of +6.0 dBm can be achieved

with a 600  termination. In this mode, the DAA will transmit and receive +1.5 dBV into all reference impedances.

3. Receive full-scale level produces –0.9 dBFS at DTX.

4. DR = 20 x log (RMS VFS/RMS Vin) + 20 x log (RMS Vin/RMS noise). The RMS noise measurement excludes

harmonics. Here, VFS is the 0 dBm full-scale level per Note 1 above.

5. Measurement is 300 to 3400 Hz. Applies to both transmit and receive paths.

6. Vin = 1 kHz, –3 dBFS.

7. THD = 20 x log (RMS distortion/RMS signal).

8. DRCID = 20 x log (RMS VCID/RMS VIN) + 20 x log (RMS VIN/RMS noise). VCID is the 1.5 V full-scale level with the

enhanced caller ID circuit. With the typical CID circuit, the VCID full-scale level is 6 V peak, and the DRCID decreases to

50 dB.

9. Refer to Tables 10–11 for relative gain accuracy characteristics (passband ripple).

10. Analog hybrid only. ZACIM controlled by ACIM in Register 30.

8

Rev. 1.5

Share Link: