NX3DV2567 데이터 시트보기 (PDF) - NXP Semiconductors.
부품명
상세내역
제조사
NX3DV2567 Datasheet PDF : 20 Pages
| |||
NXP Semiconductors
NX3DV2567
Low-ohmic four-pole double-throw analog switch
Table 5. Limiting values …continued
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol
Parameter
Conditions
Min
Max
Unit
Ptot
total power dissipation Tamb = 40 C to +125 C
[3][4] -
250
mW
[1] The minimum input voltage rating may be exceeded if the input current rating is observed.
[2] The minimum and maximum switch voltage ratings may be exceeded if the switch clamping current rating is observed but may not
exceed 4.6 V.
[3] For HXQFN16U package: above 135 C the value of Ptot derates linearly with 16.9 mW/K.
[4] For XQFN16 package: above 133 C the value of Ptot derates linearly with 14.5 mW/K.
10. Recommended operating conditions
Table 6. Recommended operating conditions
Symbol Parameter
Conditions
VCC
VI
VSW
Tamb
t/V
supply voltage
input voltage
switch voltage
ambient temperature
input transition rise and fall rate
select input S
VCC = 1.4 V to 4.3 V
Min
1.4
0
[1] 0
40
[2] -
Max
4.3
4.3
VCC
+125
200
Unit
V
V
V
C
ns/V
[1] To avoid sinking GND current from terminal nZ when switch current flows in terminal nYn, the voltage drop across the bidirectional
switch must not exceed 0.4 V. If the switch current flows into terminal nZ, no GND current will flow from terminal nYn. In this case, there
is no limit for the voltage drop across the switch.
[2] Applies to control signal levels.
11. Static characteristics
Table 7. Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground 0 V).
Symbol Parameter Conditions
Tamb = 25 C
Min Typ Max
VIH
HIGH-level VCC = 1.4 V to 1.6 V
input voltage VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
VIL
LOW-level
VCC = 1.4 V to 1.6 V
input voltage VCC = 1.65 V to 1.95 V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VCC = 3.6 V to 4.3 V
II
input leakage select input S;
current
VI = GND to 4.3 V;
VCC = 1.4 V to 4.3 V
0.9
-
-
0.9
-
-
1.1
-
-
1.3
-
-
1.4
-
-
-
-
0.3
-
-
0.4
-
-
0.4
-
-
0.5
-
-
0.6
-
-
-
Tamb = 40 C to +125 C Unit
Min Max Max
(85 C) (125 C)
0.9
-
-V
0.9
-
-V
1.1
-
-V
1.3
-
-V
1.4
-
-V
-
0.3
0.3 V
-
0.4
0.3 V
-
0.4
0.4 V
-
0.5
0.5 V
-
0.6
0.6 V
-
0.5
1 A
NX3DV2567
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 9 November 2011
© NXP B.V. 2011. All rights reserved.
5 of 20
Share Link: 