ISP1102 데이터 시트보기 (PDF) - NXP Semiconductors.
부품명
상세내역
제조사
ISP1102 Datasheet PDF : 26 Pages
| |||
NXP Semiconductors
ISP1102
Advanced USB transceiver
Table 11. Static characteristics: supply pins …continued
VCC(5V0) = 4.0 V to 5.5 V or V(VREG3V3) = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; VGND = 0 V; see Table 8 for valid voltage
level combinations; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max Unit
ICC(susp)
suspend supply current
SUSPEND = HIGH
[4] -
-
20
µA
ICC(I/O)(sharing) sharing mode supply current VCC(5V0) < 3.6 V
on pin VCC(I/O)
-
-
20
µA
Iload(sharing)DM sharing mode load current on VCC(5V0) < 3.6 V; SOFTCON =
pin DM
LOW; VDM = 3.6 V
-
-
10
µA
Iload(sharing)DP sharing mode load current on VCC(5V0) < 3.6 V; SOFTCON =
pin DP
LOW; VDP = 3.6 V
-
-
10
µA
VCC(5V0)th
supply voltage detection
threshold (5.0 V)
1.65 V ≤ VCC(I/O) ≤ 3.6 V
supply lost
-
-
3.6
V
supply present
4.1
-
-
V
VCC(5V0)hys
supply voltage detection
hysteresis (5.0 V)
VCC(I/O) = 1.8 V
-
70
-
mV
VCC(I/O)th
supply voltage detection
threshold (I/O)
V(VREG3V3) = 2.7 V to 3.6 V
supply lost
-
-
0.5
V
supply present
1.4
-
-
V
VCC(I/O)(hys) supply voltage detection
hysteresis (I/O)
V(VREG3V3) = 3.3 V
-
0.45 -
V
VREG(3V3)th
regulated supply voltage
detection threshold (3.3 V)
1.65 V ≤ VCC(I/O) ≤ V(VREG3V3);
2.7 V ≤ V(VREG3V3) ≤ 3.6 V
supply lost
-
-
0.8
V
supply present
[5] 2.4
-
-
V
VREG(3V3)hys regulated supply voltage
detection hysteresis (3.3 V)
VCC(I/O) = 1.8 V
-
0.45 -
V
[1] Iload includes the pull-up resistor current through pin VPU3V3.
[2] The minimum voltage is 2.7 V in suspend mode.
[3] Maximum value characterized only, not tested in production.
[4] Excluding any load current and VPU3V3 or VSW source current to the 1.5 kΩ and 15 kΩ pull-up and pull-down resistors (200 µA typ.).
[5] When VCC(I/O) < 2.7 V, the minimum value for VREG(3V3)th = 2.0 V for supply present condition.
Table 12. Static characteristics: digital pins
VCC(I/O) = 1.65 V to 3.6 V; VGND = 0 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
VCC(I/O) = 1.65 V to 3.6 V
Input levels
VIL
VIH
Output levels
LOW-level input voltage
HIGH-level input voltage
-
-
0.6VCC(I/O)
-
VOL
LOW-level output voltage
IOL = 100 µA
-
-
IOL = 2 mA
-
-
VOH
HIGH-level output voltage
IOH = 100 µA
VCC(I/O) − 0.15 -
IOH = 2 mA
VCC(I/O) − 0.4
-
Max
Unit
0.3VCC(I/O)
V
-
V
0.15
V
0.4
V
-
V
-
V
ISP1102_5
Product data sheet
Rev. 05 — 11 December 2007
© NXP B.V. 2007. All rights reserved.
10 of 25
Share Link: 