ICL7106CPL_98 데이터 시트보기 (PDF) - Intersil
부품명
상세내역
제조사
ICL7106CPL_98 Datasheet PDF : 16 Pages
| |||
ICL7106, ICL7107, ICL7106S, ICL7107S
Absolute Maximum Ratings
Supply Voltage
ICL7106, V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15V
ICL7107, V+ to GND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6V
ICL7107, V- to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-9V
Analog Input Voltage (Either Input) (Note 1). . . . . . . . . . . . . V+ to V-
Reference Input Voltage (Either Input) . . . . . . . . . . . . . . . . . V+ to V-
Clock Input
ICL7106 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TEST to V+
ICL7107 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND to V+
Thermal Information
Thermal Resistance (Typical, Note 2)
θJA (oC/W)
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
MQFP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150oC
Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC
(MQFP - Lead Tips Only)
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . .0oC to 70oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Input voltages may exceed the supply voltages provided the input current is limited to ±100µA.
2. θJA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications (Note 3)
PARAMETER
TEST CONDITIONS
MIN TYP MAX
UNIT
SYSTEM PERFORMANCE
Zero Input Reading
VIN = 0.0V, Full Scale = 200mV
-000.0 ±000.0 +000.0 Digital
Reading
Stability (Last Digit) (ICL7106S, ICL7107S
Only)
Fixed Input Voltage (Note 7)
-000.0 ±000.0 +000.0 Digital
Reading
Ratiometric Reading
VlN = VREF, VREF = 100mV
999 999/10 1000
00
Digital
Reading
Rollover Error
-VIN = +VlN ≅ 200mV
Difference in Reading for Equal Positive and
Negative Inputs Near Full Scale
-
±0.2
±1
Counts
Linearity
Full Scale = 200mV or Full Scale = 2V Maximum -
Deviation from Best Straight Line Fit (Note 6)
±0.2
±1
Counts
Common Mode Rejection Ratio
Noise
VCM = 1V, VIN = 0V, Full Scale = 200mV (Note 6)
-
50
-
VIN = 0V, Full Scale = 200mV
-
15
-
(Peak-To-Peak Value Not Exceeded 95% of Time)
µV/V
µV
Leakage Current Input
Zero Reading Drift
Scale Factor Temperature Coefficient
VlN = 0 (Note 6)
VlN = 0, 0oC To 70oC (Note 6)
V(EINxt.=R1e9f9. m0pVp,m0o/oCCT) o(N7o0toeC6,)
-
1
10
pA
-
0.2
1
µV/oC
-
1
5
ppm/oC
End Power Supply Character V+ Supply
VIN = 0 (Does Not Include LED Current for ICL7107) -
1.0
1.8
mA
Current
End Power Supply Character V- Supply Current ICL7107 Only
-
0.6
1.8
mA
COMMON Pin Analog Common Voltage
25kΩ Between Common and
Positive Supply (With Respect to + Supply)
Temperature Coefficient of Analog Common 25kΩ Between Common and
Positive Supply (With Respect to + Supply)
2.4
3.0
3.2
V
-
80
-
ppm/oC
DISPLAY DRIVER ICL7106 ONLY
Peak-To-Peak Segment Drive Voltage
Peak-To-Peak Backplane Drive Voltage
V+ = to V- = 9V (Note 5)
4
5.5
6
V
3
Share Link: 