LT1195 데이터 시트보기 (PDF) - Linear Technology
부품명
상세내역
제조사
LT1195 Datasheet PDF : 12 Pages
| |||
LT1195
+–5V ELECTRICAL CHARACTERISTICS 0°C ≤ TA ≤ 70°C
VS = ±5V, Pin 5 open circuit, unless otherwise noted.
SYMBOL
VOS
∆VOS/∆T
IOS
IB
CMRR
PSRR
AVOL
VOUT
IS
IS/D
PARAMETER
Input Offset Voltage
Input VOS Drift
Input Offset Current
Input Bias Current
Common Mode Rejection Ratio
Power Supply Rejection Ratio
Large-Signal Voltage Gain
Output Voltage Swing
Supply Current
Shutdown Supply Current
Shutdown Pin Current
CONDITIONS
J8, N8 Package
S8 Package
VCM = –2.5V to 3.5V
VS = ±2.375V to ±5V
RL = 1k, VOUT = ±3V
RL = 150Ω, VOUT = ±3V
RL = 1k
Pin 5 at V – (Note 9)
Pin 5 at V –
LT1195C
MIN TYP MAX
3.0
10.0
3.0
15.0
12
0.2
1.7
±0.5 ±2.5
60
85
60
90
2.0
7.5
0.3
1.5
±3.7 ±3.9
12
17
0.9
2.0
5
25
UNITS
mV
mV
µV/°C
µA
µA
dB
dB
V/mV
V/mV
V
mA
mA
µA
5V ELECTRICAL CHARACTERISTICS 0°C ≤ TA ≤ 70°C
VS+ = 5V, VS– = OV, Pin 5 open circuit, unless otherwise noted.
SYMBOL
VOS
∆VOS/∆T
IOS
IB
CMRR
VOUT
PARAMETER
Input Offset Voltage
Input VOS Drift
Input Offset Current
Input Bias Current
Input Voltage Range
Common Mode Rejection Ratio
Output Voltage Swing
IS
Supply Current
Shutdown Supply Current
IS/D
Shutdown Pin Current
CONDITIONS
J8, N8 Package
S8 Package
(Note 4)
VCM = 2V to 3.5V
RL = 150Ω to Ground
Pin 5 at V– (Note 9)
Pin 5 at V–
VOUT High
VOUT Low
LT1195C
MIN TYP MAX
1.0
10.0
1.0
15.0
15
0.2
1.7
±0.5 ±2.5
2.0
3.5
60
85
3.5
3.75
0.15
0.4
12
16
0.9
2.0
5
25
UNITS
mV
mV
µV/°C
µA
µA
V
dB
V
V
mA
mA
µA
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: A heat sink may be required to keep the junction temperature
below absolute maximum when the output is shorted continuously.
Note 3: TJ is calculated from the ambient temperature TA and power
dissipation PD according to the following formats:
LT1195MJ8/LT1195CJ8: TJ = TA + (PD • 100°C/ W)
LT1195N:
TJ = TA + (PD • 100°C/ W)
LT1195CS:
TJ = TA + (PD • 150°C/ W)
Note 4: Exceeding the input common mode range may cause the output
to invert.
Note 5: Slew rate is measured between ±1V on the output, with ±3V input
step.
Note 6: Full power bandwidth is calculated from the slew rate
measurement: FPBW = SR/2πVP.
Note 7: Settling time measurement techniques are shown in “Take the
Guesswork Out of Settling Time Measurements,” EDN, September 19, 1985.
Note 8: NTSC (3.58MHz). For RL = 1k, Diff AV = 0.3%, Diff Ph = 0.35°.
Note 9: See Applications Information section for shutdown at elevated
temperatures. Do not operate the shutdown above TJ > 125°C.
Note 10: AC parameters are 100% tested on the ceramic and plastic DIP
packaged parts (J8 and N8 suffix) and are sample tested on every lot of
the SO packaged parts (S8 suffix).
Note 11: Do not operate at AV < 2 for TA < 0°C.
1195fa
4
Share Link: 