LT3430_02 데이터 시트보기 (PDF) - Linear Technology
부품명
상세내역
제조사
LT3430_02 Datasheet PDF : 28 Pages
| |||
LT3430
ELECTRICAL CHARACTERISTICS
The q denotes specifications which apply over the full operating temperature range, otherwise specifications are at TJ = 25°C.
VIN = 15V, VC = 1.5V, SHDN = 1V, BOOST = Open Circuit, SW = Open Circuit, unless otherwise noted.
PARAMETER
CONDITIONS
MIN TYP MAX
Minimum Input Voltage
(Note 3)
q
4.6 5.5
Minimum Boost Voltage
Boost Current (Note 5)
Input Supply Current (IVIN)
Bias Supply Current (IBIAS)
Shutdown Supply Current
(Note 4) ISW ≤ 3A
q
Boost = VIN + 5V, ISW = 1A
q
Boost = VIN + 5V, ISW = 3A
q
(Note 6) VBIAS = 5V
(Note 6) VBIAS = 5V
SHDN = 0V, VIN ≤ 60V, SW = 0V, VC Open
q
1.8 3
25 50
75 120
1.5 2.2
3.1 4.2
35 100
200
Lockout Threshold
Shutdown Thresholds
Minimum SYNC Amplitude
VC Open
– 40°C ≤ TJ < 25°C
25°C ≤ TJ ≤ 125°C
VC Open, Shutting Down
VC Open, Starting Up
2.2
2.48
2.3 2.38 2.48
q 0.15 0.37 0.58
q 0.25 0.42 0.60
1.5
SYNC Frequency Range
228
700
SYNC Input Resistance
20
UNITS
V
V
mA
mA
mA
mA
µA
µA
V
V
V
V
V
kHz
kΩ
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: Gain is measured with a VC swing equal to 200mV above the low
clamp level to 200mV below the upper clamp level.
Note 3: Minimum input voltage is not measured directly, but is guaranteed
by other tests. It is defined as the voltage where internal bias lines are still
regulated so that the reference voltage and oscillator remain constant.
Actual minimum input voltage to maintain a regulated output will depend
upon output voltage and load current. See Applications Information.
Note 4: This is the minimum voltage across the boost capacitor needed to
guarantee full saturation of the internal power switch.
Note 5: Boost current is the current flowing into the BOOST pin with the
pin held 5V above input voltage. It flows only during switch on time.
Note 6: Input supply current is the quiescent current drawn by the input
pin when the BIAS pin is held at 5V with switching disabled. Bias supply
current is the current drawn by the BIAS pin when the BIAS pin is held at
5V. Total input referred supply current is calculated by summing input
supply current (IVIN) with a fraction of bias supply current (IBIAS):
ITOTAL = IVIN + (IBIAS)(VOUT/VIN)
With VIN = 15V, VOUT = 5V, IVIN = 1.4mA, IBIAS = 2.9mA, ITOTAL = 2.4mA.
Note 7: Switch on resistance is calculated by dividing VIN to SW voltage by
the forced current (3A). See Typical Performance Characteristics for the
graph of switch voltage at other currents.
Note 8: The LT3430EFE is guaranteed to meet performance specifications
from 0°C to 125°C junction temperature. Specifications over the –40°C to
125°C operating junction temperature range are assured by design,
characterization and correlation with statistical process controls. The
LT3430IFE is guaranteed over the full –40°C to 125°C operating junction
temperature range.
Note 9: See Peak Switch Current Limit vs Junction Temperature graph in
the Typical Performance Characteristics section.
sn3430 3430is
3
Share Link: 