MC100LVE222(2000) 데이터 시트보기 (PDF) - ON Semiconductor
부품명
상세내역
제조사
MC100LVE222 Datasheet PDF : 8 Pages
| |||
MC100LVE222
ECL AC CHARACTERISTICS (VEE = VEE (min) to VEE (max); VCC = VCCO = GND)
–40°C
0°C
25°C
70°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Min Typ Max Unit Condition
tPLH
tPHL
Propagation Delay to Out-
ps
put
1040 1140 1240 1060 1160 1260 1080 1180 1280 1120 1220 1320
IN (differential) 990 1140 1290 1010 1160 1310 1030 1180 1330 1070 1220 1370
IN (single–ended) 1100 1250 1400 1130 1280 1430 1170 1320 1470 1220 1370 1520
MR
Note 1.
Note 2.
tskew
Within–Device Skew
Part–to–Part Skew (Diff)
50
50
50
50
ps
Note 3.
200
200
200
200
VPP
VCMR
Minimum Input Swing
400
Common Mode Range
VPP < 500mV
VEE
+1.3
400
–0.4 VEE
+1.2
400
–0.4 VEE
+1.2
400
–0.4 VEE
+1.2
mV
V
–0.4
Note 4.
Note 5.
VPP ≥ 500mV VEE
–0.4 VEE
–0.4 VEE
–0.4 VEE
–0.4
+1.6
+1.5
+1.5
+1.5
tr/tf
Output Rise/Fall Time
200
600 200
600 200
600 200
600 ps 20%–80%
1. The differential propagation delay is defined as the delay from the crossing points of the differential input signals to the crossing point of the
differential output signals.
2. The single-ended propagation delay is defined as the delay from the 50% point of the input signal to the 50% point of the output signal.
3. The within–device skew is defined as the worst case difference between any two similar delay paths within a single device.
4. VPP(min) is defined as the minimum input differential voltage which will cause no increase in the propagation delay. The VPP(min) is AC limited
for the LVE222. A differential input as low as 50 mV will still produce full ECL levels at the output.
5. VCMR is defined as the range within which the VIH level may vary, with the device still meeting the propagation delay specification. The VIL
level must be such that the peak to peak voltage is less than 1.0 V and greater than or equal to VPP(min).
PECL AC CHARACTERISTICS (VEE = GND; VCC = VCCO = VCC (min) to VCC (max))
–40°C
0°C
25°C
70°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Min Typ Max Unit Condition
tPLH
tPHL
Propagation Delay to Out-
ps
put
1040 1140 1240 1060 1160 1260 1080 1180 1280 1120 1220 1320
IN (differential) 990 1140 1290 1010 1160 1310 1030 1180 1330 1070 1220 1370
IN (single–ended) 1100 1250 1400 1130 1280 1430 1170 1320 1470 1220 1370 1520
MR
Note 1.
Note 2.
tskew
Within–Device Skew
Part–to–Part Skew (Diff)
50
50
50
50
ps
Note 3.
200
200
200
200
VPP
VCMR
Minimum Input Swing
400
Common Mode Range
VPP < 500mV 1.3
400
VCC 1.2
–0.4
400
VCC 1.2
–0.4
400
VCC 1.2
–0.4
mV
V
VCC
–0.4
Note 4.
Note 5.
VPP ≥ 500mV 1.6
VCC 1.5
–0.4
VCC 1.5
–0.4
VCC 1.5
–0.4
VCC
–0.4
tr/tf
Output Rise/Fall Time
200
600 200
600 200
600 200
600 ps 20%–80%
1. The differential propagation delay is defined as the delay from the crossing points of the differential input signals to the crossing point of the
differential output signals.
2. The single-ended propagation delay is defined as the delay from the 50% point of the input signal to the 50% point of the output signal.
3. The within–device skew is defined as the worst case difference between any two similar delay paths within a single device.
4. VPP(min) is defined as the minimum input differential voltage which will cause no increase in the propagation delay. The VPP(min) is AC limited
for the LVE222. A differential input as low as 50 mV will still produce full ECL levels at the output.
5. VCMR is defined as the range within which the VIH level may vary, with the device still meeting the propagation delay specification. The VIL
level must be such that the peak to peak voltage is less than 1.0 V and greater than or equal to VPP(min).
http://onsemi.com
4
Share Link: 