MC100E310FN(2002) 데이터 시트보기 (PDF) - ON Semiconductor
부품명
상세내역
제조사
MC100E310FN Datasheet PDF : 8 Pages
| |||
MC100E310
MAXIMUM RATINGS (Note 1)
Symbol
Parameter
Condition 1
Condition 2
Rating
Units
VCC
VEE
VI
Iout
PECL Mode Power Supply
NECL Mode Power Supply
PECL Mode Input Voltage
NECL Mode Input Voltage
Output Current
VEE = 0 V
VCC = 0 V
VEE = 0 V
VCC = 0 V
Continuous
Surge
VI VCC
VI VEE
8
V
–8
V
6
V
–6
V
50
mA
100
mA
IBB
VBB Sink/Source
TA
Operating Temperature Range
± 0.5
mA
0 to +85
°C
Tstg
Storage Temperature Range
θJA
Thermal Resistance (Junction to Ambient) 0 LFPM
500 LFPM
28 PLCC
28 PLCC
–65 to +150
63.5
43.5
°C
°C/W
°C/W
θJC
VEE
Thermal Resistance (Junction to Case)
PECL Operating Range
NECL Operating Range
std bd
28 PLCC
22 to 26
4.2 to 5.7
–5.7 to –4.2
°C/W
V
V
Tsol
Wave Solder
<2 to 3 sec @ 248°C
1. Maximum Ratings are those values beyond which device damage may occur.
265
°C
100E SERIES PECL DC CHARACTERISTICS VCCx= 5.0 V; VEE= 0.0 V (Note 1)
–40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VBB
VIHCMR
Power Supply Current
Output HIGH Voltage (Note 2)
Output LOW Voltage (Note 2)
Input HIGH Voltage (Single Ended)
Input LOW Voltage (Single Ended)
Output Voltage Reference
Input HIGH Voltage Common Mode
Range (Differential) (Note 3)
55
60
55
60
65
70
mA
3915 3995 4120 3975 4050 4120 3975 4050 4120 mV
3170 3305 3445 3190 3255 3380 3190 3260 3380 mV
3835 4050 4120 3835 4120 4120 3835 4120 4120 mV
3190 3300 3525 3190 3525 3525 3190 3525 3525 mV
3.62
3.74 3.62
3.74 3.62
3.74 V
2.7
4.6 2.7
4.6 2.7
4.6
V
IIH
Input HIGH Current
150
150
150 µA
IIL
Input LOW Current
0.5 0.3
0.5 0.25
0.5 0.2
µA
NOTE: Devices are designed to meet the DC specifications shown in the above table, after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained.
1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.46 V / –0.8 V.
2. Outputs are terminated through a 50 ohm resistor to VCC–2 volts.
3. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC.
100E SERIES NECL DC CHARACTERISTICS VCCx= 0.0 V; VEE= –5.0 V (Note 1)
0°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VBB
VIHCMR
Power Supply Current
Output HIGH Voltage (Note 2)
Output LOW Voltage (Note 2)
Input HIGH Voltage (Single Ended)
Input LOW Voltage (Single Ended)
Output Voltage Reference
Input HIGH Voltage Common Mode
Range (Differential) (Note 3)
55
60
55
60
65
70
mA
–1085 –1005 –880 –1025 –950 –880 –1025 –950 –880 mV
–1830 –1695 –1555 –1810 –1745 –1620 –1810 –1740 –1620 mV
–1165 –950 –880 –1165 –880 –880 –1165 –880 –880 mV
–1810 –1700 –1475 –1810 –1475 –1475 –1810 –1475 –1475 mV
–1.38
–1.26 –1.38
–1.26 –1.38
–1.26 V
–2.3
–0.4 –2.3
–0.4 –2.3
–0.4 V
IIH
Input HIGH Current
150
150
150 µA
IIL
Input LOW Current
0.5 0.3
0.5 0.25
0.5 0.2
µA
NOTE: Devices are designed to meet the DC specifications shown in the above table, after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained.
1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.46 V / –0.8 V.
2. Outputs are terminated through a 50 ohm resistor to VCC–2 volts.
3. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC.
http://onsemi.com
3
Share Link: 