MC100EL39DWG 데이터 시트보기 (PDF) - ON Semiconductor
부품명
상세내역
제조사
MC100EL39DWG Datasheet PDF : 7 Pages
| |||
MC100EL39
Table 5. 100EL SERIES NECL DC CHARACTERISTICS VCC = 0.0 V; VEE = −5.0 V (Note 4)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
Power Supply Current
50
59
50
59
54
61 mA
VOH
Output HIGH Voltage (Note 5)
−1085 −1005 −880 −1025 −955 −880 −1025 −955 −880 mV
VOL
Output LOW Voltage (Note 5)
−1830 −1695 −1555 −1810 −1705 −1620 −1810 −1705 −1620 mV
VIH
Input HIGH Voltage (Single−Ended) −1165
−880 −1165
−880 −1165
−880 mV
VIL
Input LOW Voltage (Single−Ended) −1810
−1475 −1810
−1475 −1810
−1475 mV
VBB
Output Voltage Reference
−1.38
−1.26 −1.38
−1.26 −1.38
−1.26 V
VIHCMR Common Mode Range (Differential)
(Note 6)
VPP < 500 mV −3.7
VPP ≥ 500 mV −3.5
−0.4 −3.8
−0.4 −3.6
−0.4 −3.8
−0.4 −3.6
V
−0.4
−0.4
IIH
Input HIGH Current
150
150
150 mA
IIL
Input LOW Current
0.5
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification
limit values are applied individually under normal operating conditions and not valid simultaneously.
4. Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / −0.5 V.
5. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.
6. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input
signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1.0 V.
Table 6. AC CHARACTERISTICS VCC = 5.0 V; VEE = 0.0 V or VCC = 0.0 V; VEE = −5.0 V (Note 7)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
fMAX
tPLH
tPHL
Maximum Toggle Frequency
1.0
Propagation Delay to Output
CLK → Q (Differential) 850
CLK → Q (Single−Ended) 850
MR → Q 600
1.0
1150 900
1150 900
900 610
1.0
1200 950
1200 950
910 630
1250
1250
930
GHz
ps
tSKEW Within-Device Skew (Note 8) Q0 − Q3
50
50
50
ps
Part-to-Part
Q0 − Q3 (Diff)
200
200
200
tJITTER Random CLOCK Jitter (RMS) @ 1.0 GHz
2.0 3.0
2.0 3.0
2.0 3.0 ps
tS
Setup Time
EN → CLK 250
250
250
ps
DIVSEL → CLK 400
400
400
tH
Hold Time
CLK → EN 100
100
100
ps
CLK → Div_Sel 150
150
150
VPP
Input Swing (Note 9)
tRR
Reset Recovery Time
tPW
Minimum Pulse Width
150
CLK 500
MR 700
1000 150
100
500
700
1000 150
100
500
700
1000 mV
100 ps
ps
tr, tf
Output Rise/Fall Times Q (20% − 80%) 280
550 280
550 280
550 ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification
limit values are applied individually under normal operating conditions and not valid simultaneously.
7. VEE can vary +0.8 V / −0.5 V. Outputs are terminated through 50 W resistor to VCC − 2.0 V.
8. Skew is measured between outputs under identical transitions.
9. VPP(min) is minimum input swing for which AC parameters guaranteed. The device has a DC gain of ≈40.
http://onsemi.com
4
Share Link: 