MC10192 데이터 시트보기 (PDF) - Motorola => Freescale

부품명

상세내역

제조사

MC10192

Quad Bus Driver

Motorola => Freescale 

MC10192

ELECTRICAL CHARACTERISTICS

Characteristic

Symbol

Pin

Under

Test

–30°C

Min

Max

Test Limits

+25°C

Min

Max

+85°C

Min

Max

Power Supply Drain Current

IE

8

154

140

154

Input Current

IinH

5

350

220

220

IinL

5

0.5

0.5

0.3

Output Current High

Logic 1 IOH

2

2.0

Output Current Low

Logic 0 IOL

2

13.5

18.0

14.0

18.0

14.0

19.0

Threshold Current High

Logic 1 IOHC

2

2.0

2.0

2.0

Threshold Current Low

Logic 0 IOLC

2

13.5

14.0

14.0

Output Sink Current Low

Logic 0 IOS

2

13.3

13.9

13.3

Load Return Voltage Absolute Max

Rating (Note 1.)

VLR

5.5

5.5

5.5

Output Voltage Low (Note 2.)

VOLS

–2.4

Switching Times

(50Ω Load)

Propagation Delay

Rise/Fall Time

E to Output

D to Output

(20 to 80%)

tPHL

tPLH

tTLH

tTHL

2.0

6.0

1.5

4.5

3.3

1. The 5.5V value is a maximum rating, do not exceed. A 270Ω resistor will prevent output transistor breakdown.

2. Limitations of load resistor and load return voltage combinations. Refer to page 3–160 description.

Unit

mAdc

µAdc

µAdc

mAdc

mAdc

mAdc

mAdc

mAdc

V

V

ns

ELECTRICAL CHARACTERISTICS (continued)

TEST VOLTAGE VALUES (Volts)

@ Test Temperature VIHmax

–30°C –0.890

VILmin

–1.890

VIHAmin VILAmax

–1.205

–1.500

VEE

–5.2

+25°C –0.810

–1.850

–1.105

–1.475

–5.2

+85°C –0.700

–1.825

–1.035

–1.440

–5.2

Characteristic

Symbol

Power Supply Drain Current

Input Current

Output Current High

Logic 1

Output Current Low

Logic 0

Threshold Current High

Logic 1

Threshold Current Low

Logic 0

Output Sink Current Low

Logic 0

Load Return Voltage Absolute Max

Rating (Note 1.)

IE

IinH

IinL

IOH

IOL

IOHC

IOLC

IOS

VLR

Pin

Under

Test

8

5

5

2

2

2

2

TEST VOLTAGE APPLIED TO PINS LISTED BELOW

VIHmax VILmin VIHAmin VILAmax

5

5

5,6,10,11

5,6,10,11

5,7,9,10,11

6

5,10,11

7,9

6

5,6,10,11

VEE

8

8

8

8

8

8

8

8

8

(VCC)

Gnd

16

16

16

16

16

16

16

16

16

Output Voltage Low (Note 2.)

VOLS

8

16

Each MECL 10,000 series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been

established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained.

Outputs are terminated through a 50–ohm resistor to –2.0 volts. Test procedures are shown for only one gate. The other gates are tested in the

same manner.

MECL Data

DL122 — Rev 6

3–161

MOTOROLA

Share Link: