OPL530 데이터 시트보기 (PDF) - TT Electronics.
부품명
상세내역
제조사
OPL530 Datasheet PDF : 10 Pages
| |||
OPL530, OPL531, OPL535, OPL536, OPL550,
OPL551, OPL560, OPL561, OPL562, OPL563
Electrical Characteristics (TA = 25° C unless otherwise noted)
SYMBOL
PARAMETER
MIN TYP MAX UNITS
TEST CONDITIONS
Output Rise Time
OPL530
OPL530-OC,
OPL536-OC
OPL550
tr
OPL550-OC, OPL551-OC
OPL560, OPL561
OPL561-OC
Output Rise Time
OPL530
-
1.5 -
-
50 -
-
25 70
-
25 70
-
-
70
-
-
100
-
-
-
µs EE = 0 or 1 mW/cm2, CL = 50 pF
ns EE = 0 or 1 mW/cm2, RL = 300 Ω to 5 V,
CL = 50 Pf
ns VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2,
f = 10 kHz, DC = 50%
RL = 8 TTL loads
ns VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2,
f = 10 kHz, DC = 50%,
RL = 360 Ω
ns TA = 25° C, EE = 0 or 1 mW/cm2,
f = 10 kHz, DC = 50%,
µs RL = 360 Ω
µs EE = 0 or 1 mW/cm2, CL = 50 pF
OPL530-OC,
OPL536-OC
-
-
-
ns EE = 0 or 1 mW/cm2, RL = 300 Ω to 5 V,
CL = 50 pF
OPL550-OC, OPL551-OC
tr
OPL561-OC
OPL560, OPL561
OPL561-OC
-
25 70
-
-
70
-
-
70
-
-
100
ns VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2,
RL = 8 TTL loads,
f = 10 kHz, DC = 50%
ns VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2,
RL = 8 TTL loads,
f = 10 kHz, DC = 50%
ns TA = 25° C, EE = 0 or 1 mW/cm2,
f = 10 kHz
ns TA = 25° C, EE = 0 or 1 mW/cm2,
f = 10 kHz
Output Fall Time
OPL530
-
20 -
ns EE = 0 or 1 mW/cm2, CL = 50 Pf
OPL530-OC,
OPL536-OC
-
20 -
ns EE = 0 or 1 mW/cm2, RL = 300 Ω to 5 V,
CL = 50 pF
tf
Notes:
(1)
(2)
(3)
(4)
OPL550-OC, OPL551-OC
OPL560, OPL561
OPL561-OC
-
25 70
-
-
70
-
-
100
ns VCC = 5 V, TA = 25° C, EE = 0 or 3 mW/cm2,
RL = 360 Ω, f = 10 kHz, DC = 50%
TA = 25° C, EE = 0 or 1 mW/cm2,
ns f = 10 kHz
TA = 25° C, EE = 0 or 1 mW/cm2,
ns f = 10 kHz
RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. For OPL530, OPL530-OC, and OPL536-OC, a maximum of 20 grams
force may be applied to leads while at soldering temperatures.
Derate linearly 2.67 mW/°C above 70° C for OPL530, OPL530-OC and OPL536-OC. Derate linearly 2.5 mW/° C above 25° C for all devices in the OPL550, OPL560,
OPL561, OPL562 and OPL563 series.
Irradiance measurements are made with λi = 935 nm.
This applies to OC versions only. For ICC on pull-up versions, add VCC/10 KΩ.
General Note
TT Electronics reserves the right to make changes in product specification without
notice or liability. All information is subject to TT Electronics’ own data and is
considered accurate at time of going to print.
© TT electronics plc
OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
www.optekinc.com | www.ttelectronics.com
Issue C 09/2016 Page 9
Share Link: 