OMR1033NM 데이터 시트보기 (PDF) - Omnirel Corp => IRF
부품명
상세내역
제조사
OMR1033NM Datasheet PDF : 6 Pages
| |||
OMR1033SR, OMR1033ST, OMR1033NM
ELECTRICAL CHARACTERISTICS -55°C ≤ TA ≤ +125°C (unless otherwise specified)
Parameter
Symbol
Test Conditions
Min.
Max.
Reference Voltage
Line Regulation
(Note 1)
Load Regulation
(Note 1)
Thermal Regulation
Ripple Rejection
(Note 2)
Adjust Pin Current
Adjust Pin Current Change
Minimum Load Current
Current Limit
VREF
ÁVIN - VOUT Í = 5 V, IOUT = 5 mA, TA = 25° C
3 V ≤ ÁVIN - VOUT Í ≤ 35 V
•
∆VOUT
∆VIN
3 V ≤ ÁVIN - VOUT Í ≤ 35 V
•
∆VOUT
ÁVOUT Í ≤ 5 V, TA = 25° C
∆IOUT
10 mA ≤ IOUT ≤ IMAX.
•
ÁVOUT Í≥ 5.0 V
10 mA ≤ IOUT ≤ IMAX.
•
-
30 ms pulse, TA = 25° C
∆VIN
∆VREF
ÁVOUT Í= -10 V, f = 120 Hz, CAdj = 0
•
ÁVOUT Í= -10 V, f = 120 Hz, CAdj = 10 µF
•
IAdj
∆IAdj
IMin
VDIFF = 35 V, IL = 10 mA
•
10 mA ≤ IOUT ≤ IMAX.
•
3 V ≤ ÁVIN - VOUT Í ≤ 35 V
•
ÁVIN - VOUT Í ≤ 35 V
•
ÁVIN - VOUT Í ≤ 10 V
•
ILim
ÁVIN - VOUT Í ≤ 10 V
•
-1.238
-1.215
56
53
70
60
3.0
3.0
-1.262
-1.285
0.015
0.04
50
75
1.0
1.5
0.02
100
2.0
5.0
5.0
3.0
6.0
ÁVIN - VOUT Í = 35 V
0.5
2.5
•
0.5
Temperature Stability
(Note 2)
∆VOUT
∆T
-55° C ≤ TJ ≤ +125° C
•
1.5
Long Term Stability
(Note 2)
∆VOUT
∆T
TA = +125° C, t = 1000 hrs
1.0
Unit
V
%/V
mV
%
%/W
dB
dB
µA
µA
mA
A
A
%
%
Notes:
1. Line and Load Regulation are measured at a constant junction temperature using a low duty cycle pulse technique.
Although power dissipation is internally limited, regulation is guaranteed up to the maximum power dissipation of 30 W.
Power dissipation is determined by the input/output differential voltage and the output current. Guaranteed maximum
power dissipation will not be available over the full input/output voltage range.
2. Guaranteed by design, characterization or correlation to other tested parameters.
3. The • denotes the specifications which apply over the full operating temperature range.
4. Refer to curves for typical characteristics versus total dose radiation levels.
RADIATION TEST PROGRAM
The following chart is a summary of the test data collected on Radiation Tolerant OMR1033 at
various dose rates. The chart depicts the Total Radiation Dose that each device was exposed to
prior to failure. Failure is defined as any electrical test that does not meet the limits of the device
per the published data sheet specifications after radiation testing.
Omnirel P/N
OMR1033SR
Test Points
5K 10K 20K 30K
XX
50K 60K 70K 80K 100K 150K 200K
Share Link: 