RT8004A 데이터 시트보기 (PDF) - Richtek Technology
부품명
상세내역
제조사
RT8004A Datasheet PDF : 13 Pages
| |||
Application Information
The basic RT8004A application circuit is shown in Typical
Application Circuit. External component selection is
determined by the maximum load current and begins with
the selection of the inductor value and operating frequency
followed by CIN and COUT.
Operating Frequency
Selection of the operating frequency is a tradeoff between
efficiency and component size. High frequency operation
allows the use of smaller inductor and capacitor values.
Operation at lower frequencies improves efficiency by
reducing internal gate charge and switching losses but
requires larger inductance values and/or capacitance to
maintain low output ripple voltage.
The operating frequency of the RT8004A is determined
by an external resistor that is connected between the RT
pin and ground. The value of the resistor sets the ramp
current that is used to charge and discharge an internal
timing capacitor within the oscillator. Although frequencies
as high as 4MHz are possible, the minimum on-time of
the RT8004A imposes a minimum limit on the operating
duty cycle. The minimum on-time is typically 110ns.
Therefore, the minimum duty cycle is equal to 100 x 110ns
x f(Hz).
Inductor Selection
For a given input and output voltage, the inductor value
and operating frequency determine the ripple current. The
ripple current ΔIL increases with higher VIN and decreases
with higher inductance.
ΔIL
=
⎡
⎢⎣
VOUT
f ×L
⎤
⎥⎦
⎡
⎢1
⎣
−
VOUT
VIN
⎤
⎥
⎦
Having a lower ripple current reduces the ESR losses in
the output capacitors and output voltage ripple. Highest
efficiency operation is achieved at low frequency with small
ripple current. This, however, requires a large inductor.
A reasonable starting point for selecting the ripple current
is ΔIL = 0.4(IMAX). The largest ripple current occurs at the
highest VIN. To guarantee that the ripple current stays
below a specified maximum, the inductor value should be
chosen according to the following equation :
RT8004A
L
=
⎡
⎢⎣ f
×
VOUT
ΔIL(MAX)
⎤
⎥⎦
⎡
⎢1−
⎢⎣
VOUT
VIN(MAX)
⎤
⎥
⎥⎦
Inductor Core Selection
Once the value for L is known, the type of inductor must
be selected. High efficiency converters generally cannot
afford the core loss found in low cost powdered iron cores,
forcing the use of more expensive ferrite or mollypermalloy
cores. Actual core loss is independent of core size for a
fixed inductor value but it is very dependent on the
inductance selected. As the inductance increases, core
losses decrease. Unfortunately, increased inductance
requires more turns of wire and, therefore higher copper
loss.
Ferrite designs have very low core losses and are preferred
at high switching frequencies, so design goals can
concentrate on copper loss and saturation prevention.
Ferrite core material saturates “hard”, which means that
inductance collapses abruptly when the peak design
current is exceeded. This results in an abrupt increase in
inductor ripple current and consequent output voltage ripple.
Do not allow the core to saturate!
Different core materials and shapes will change the size/
current and price/current relationship of an inductor.
Toroid or shielded pot cores in ferrite or permalloy materials
are small and don’ t radiate energy, but generally cost
more than powdered iron core inductors with similar
characteristics. The choice of which style inductor to use
mainly depends on the price vs size requirements and
any radiated field/EMI requirements.
CIN and COUT Selection
The input capacitance, CIN, is needed to filter the
trapezoidal current at the source of the top MOSFET. To
prevent large ripple voltage, a low ESR input capacitor
sized for the maximum RMS current should be used. RMS
current is given by :
IRMS
= IOUT(MAX)
VOUT
VIN
VIN − 1
VOUT
DS8004A-03 March 2011
www.richtek.com
9
Share Link: 