DatasheetQ Logo
Electronic component search and free download site. Transistors,MosFET ,Diode,Integrated circuits

EL5220TIYZ-T7 데이터 시트보기 (PDF) - Renesas Electronics

부품명
상세내역
제조사
EL5220TIYZ-T7 Datasheet PDF : 15 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
EL5220T
Electrical Specifications VS+ = +18V, VS- = 0V, RL = 10kΩ to 9V, TA = +25°C, unless otherwise specified.
PARAMETER
DESCRIPTION
CONDITIONS
MIN TYP MAX UNIT
INPUT CHARACTERISTICS
VOS
TCVOS
Input Offset Voltage
VCM = 9V
Average Offset Voltage Drift (Note 8) 8 Ld MSOP package
8 Ld DFN package
5
18 mV
6
µV/°C
4
µV/°C
IB
RIN
CIN
CMIR
Input Bias Current
Input Impedance
Input Capacitance
Common-Mode Input Range
VCM = 9V
-0.5
2
50
nA
1
GΩ
2
pF
+18.5 V
CMRR
Common-Mode Rejection Ratio
AVOL
Open Loop Gain
OUTPUT CHARACTERISTICS
For VINx from -0.5V to +18.5V
0.5V VOUTx 17.5V
53
78
dB
75
90
dB
VOL
VOH
ISC
Output Swing Low
Output Swing High
Short Circuit Current
IOUT
Output Current
POWER SUPPLY PERFORMANCE
IL = -9mA
120 150 mV
IL = +9mA
17.85 17.88
V
VCM = 9V, Source: VOUTx short to VS-,
Sink: VOUTx short to VS+
±200
mA
±65
mA
(VS+) - (VS-) Supply Voltage Range
IS
Supply Current (Per Amplifier)
PSRR
Power Supply Rejection Ratio
VCM = 9V, No load
Supply is moved from 4.5V to 19V
4.5
19
V
650 850 µA
60
75
dB
DYNAMIC PERFORMANCE
SR
tS
BW
GBWP
PM
CS
Slew Rate (Note 9)
Settling to +0.1% (Note 10)
-3dB Bandwidth
Gain-Bandwidth Product
Phase Margin
Channel Separation
1V VOUTx 17V, 20% to 80%
AV = +1, VOUTx = 2V step,
RL = 10kΩ, CL = 8pF
RL = 10kΩ, CL = 8pF
AV = -50, RF = 5kΩRG = 100Ω
RL = 10kΩ, CL = 8pF
AV = -50, RF = 5kΩRG = 100Ω
RL = 10kΩ, CL = 8pF
f = 5MHz
12
V/µs
500
ns
12
MHz
8
MHz
50
°
85
dB
NOTES:
8. Measured over -40°C to +85°C ambient operating temperature range. See the typical TCVOS production distribution shown in
the “Typical Performance Curves” on page 6.
9. Typical slew rate is an average of the slew rates measured on the rising (20% to 80%) and the falling (80% to 20%) edges of
the output signal.
10. Settling time measured as the time from when the output level crosses the final value on rising/falling edge to when the output
level settles within a ±0.1% error band. The range of the error band is determined by: Final Value(V)±[Full Scale(V)*0.1%]
FN6892 Rev 0.00
May 4, 2010
Page 5 of 15

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]