SY88973V 데이터 시트보기 (PDF) - Micrel

부품명

상세내역

제조사

SY88973V

3.3V/5V 3.2Gbps CML LOW-POWER LIMITING POST AMPLIFIER W/TTL LOS

Micrel 

Micrel, Inc.

3.3V/5V 3.2Gbps CML

LOW-POWER LIMITING

POST AMPLIFIER W/TTL LOS

SY88973V

SY88973V

FEATURES

DESCRIPTION

s Multi-rate up to 3.2Gbps operation

s Wide gain-bandwidth product

• 38dB differential gain

• 2GHz 3dB bandwidth

s Low noise 50Ω CML data outputs

• 800mVPP output swing

• 60ps edge rates

• 5psRMS typ. random jitter

• 15psPP typ. deterministic jitter

s Chatter-free, Loss-of-Signal (LOS) output

• 4.6dB electrical hysteresis

• OC-TTL output with internal 4.75kΩ pull-up

resistor

s Programmable LOS sensitivity using single external

resistor

s Internal 50Ω data input termination

s TTL /EN input allows feedback from LOS

s Wide operating range

• Single 3.3V ±10% or 5V ±10% power supply

• –40°C to +85°C industrial temperature range

s Available in tiny 10-pin EPAD-MSOP and

16-pin MLF™ packages

APPLICATIONS

s 1.25Gbps and 2.5Gbps Gigabit Ethernet

s 1.062Mbps and 2.125Gbps Fibre Channel

s 155Mbps, 622Gbps, 1.25Gbps, and 2.5Gbps SONET/

SDH

s Gigabit interface converter (GBIC)

s Small form factor (SFF) and small form factor

pluggable (SFP) transceivers

s Parallel 10G Ethernet

s High-gain line driver and line receiver

The SY88973V low-power, limiting post amplifier is

designed for use in fiber optic receivers. The device connects

to typical transimpedance amplifiers (TIAs). The linear signal

output from TIAs can contain significant amounts of noise

and may vary in amplitude over time. The SY88973V

quantizes these signals and outputs typically 800mVPP

voltage-limited waveforms.

The SY88973V operates from a single +3.3V ±10% or

+5V ±10% power supply, over an industrial temperature

range of –40°C to +85°C. With its wide bandwidth and high

gain, signals with data rates up to 3.2Gbps and as small as

10mVPP can be amplified to drive devices with CML inputs

or AC-coupled PECL inputs.

The SY88973V incorporates a loss-of-signal (LOS), open-

collector TTL output with internal 4.75kΩ pull-up resistor. A

programmable, loss-of-signal level set pin (LOSLVL) sets

the sensitivity of the input amplitude detection. LOS asserts

high if the input amplitude falls below the threshold set by

LOSLVL and de-asserts low otherwise. LOS can be fed

back to the enable (/EN) input to maintain output stability

under a loss-of-signal condition. /EN de-asserts the true

output signal without removing the input signal. Typically

4.6dB LOS hysteresis is provided to prevent chattering.

Please see Micrel’s website at www.micrel.com for a

complete selection of optical module ICs. The following table

summarizes the differences between devices in Micrel’s

latest family of Limiting Amplifiers.

All support documentation can be found on Micrel’s web

site at www.micrel.com.

Integrated 50Ω

Part Number Input Termination

SY88773V No

SY88823V No

SY88843V Yes

SY88973V Yes

LOS

or SD

LOS

SD

SD

LOS

Active LOW

or HIGH Enable

LOW

HIGH

HIGH

LOW

Table 1. Limiting Amplifiers Selection Guide

TYPICAL PERFORMANCE

3.3V, 25°C, 10mVpp Input

@3.2Gbps 231–1 PRBS, RLOAD = 50Ω to VCC

MicroLeadFrame and MLF are trademarks of Amkor Technology, Inc.

M9999-110905

hbwhelp@micrel.com or (408) 955-1690

1

TIME (50ps/div.)

Rev.: C Amendment: /0

Issue Date: November 2005

Share Link: