TS3022IYST 데이터 시트보기 (PDF) - STMicroelectronics
부품명
상세내역
제조사
TS3022IYST Datasheet PDF : 20 Pages
| |||
TS3022
Electrical characteristics
Table 5. Electrical characteristics at VCC = 5 V, Tamb = 25 ° C, and full Vicm range (unless otherwise specified)
Symbol
Parameter
Test conditions (1)
VIO
Input offset voltage
-40 °C < Tamb < 125 °C, TS3021A
ΔVio/ΔT Input offset voltage drift
IIO
Input offset current (2)
IIB
Input bias current (2)
ICC
Supply current
ISC
Short-circuit current
VOH
Output voltage high
VOL
Output voltage low
CMRR
SVR
Common mode rejection
ratio
Supply voltage rejection
TPLH
Propagation delay, low to
high output level (3)
TPHL
Propagation delay, high to
low output level (4)
TF
Fall time
TR
Rise time
-40 °C < Tamb < 125 °C
Tamb
-40 °C < Tamb < +125 °C
Tamb
-40 °C < Tamb < +125 °C
No load, output high, Vicm = 0 V
No load, output high, Vicm = 0 V,
-40 °C < Tamb < 125 °C
No load, output low, Vicm = 0 V
No load, output low, Vicm = 0 V,
-40 °C < Tamb < 125 °C
Source
Sink
Isource = 4 mA
-40 °C < Tamb < 125 °C
Isink = 4 mA
-40 °C < Tamb < 125 °C
0 < Vicm < 5 V
∆Vcc = 2 to 5 V
Vicm = 0 V, f = 10 kHz, CL = 50 pF,
overdrive = 100 mV
Vicm = 0 V, f = 10 kHz, CL = 50 pF,
overdrive = 20 mV
Vicm = 0 V, f = 10 kHz, CL = 50 pF,
overdrive = 100 mV
Vicm = 0 V, f = 10 kHz, CL = 50 pF,
overdrive = 20 mV
f = 10 kHz, CL = 50 pF, RL = 10 kΩ,
overdrive = 100 mV
f = 10 kHz, CL = 50 pF, RL = 10 kΩ,
overdrive = 100 mV
Min.
4.80
4.70
58
Typ.
0.2
3
1
86
77
89
51
40
4.84
130
79
73
42
54
45
55
4
4
Max.
6
7
20
20
100
160
300
95
125
115
135
180
250
75
105
75
95
Unit
mV
µV/°C
nA
µA
mA
V
mV
dB
ns
1. All values over the temperature range are guaranteed through correlation and simulation. No production test
is performed at the temperature range limits.
2. Maximum values include unavoidable inaccuracies of the industrial tests.
3. Response time is measured 10%/90% of the final output value with the following conditions: inverting input
voltage (IN-) = Vicm and non-inverting input voltage (IN+) moving from Vicm - 100 mV to Vicm + overdrive.
4. Response time is measured 10%/90% of the final output value with the following conditions: Inverting input
voltage (IN-) = Vicm and non-inverting input voltage (IN+) moving from Vicm + 100 mV to Vicm - overdrive.
DS6029 - Rev 5
page 5/20
Share Link: 