ADSP-TS101SAB2Z000 데이터 시트보기 (PDF) - Analog Devices

부품명

상세내역

제조사

ADSP-TS101SAB2Z000

TigerSHARC Embedded Processor

Analog Devices 

ADSP-TS101S

ates CCLK, which is phase-locked. The LCLKRAT pins

define the clock multiplication of LCLK to CCLK (see

Table 4). The link port clock is generated from CCLK via a

software programmable divisor. RESET must be asserted

until LCLK is stable and within specification for at least

2 ms. This applies to power-up as well as any dynamic

modification of LCLK after power-up. Dynamic modifica-

tion may include LCLK going out of specification as long as

RESET is asserted.

Connecting SCLK and LCLK to the same clock source is a

requirement for the device. Using an integer clock multiplica-

tion value provides predictable cycle-by-cycle operation, a

requirement of fault-tolerant systems and some multiprocessing

systems.

Noninteger values are completely functional and acceptable for

applications that do not require predictable cycle-by-cycle

operation.

OUTPUT PIN DRIVE STRENGTH CONTROL

Pins CONTROLIMP2–0 and DS2–0 work together to control

the output drive strength of two groups of pins, the

Address/Data/Control pin group and the Link pin group.

CONTROLIMP2–0 independently configures the two pin

groups to the maximum drive strength or to a digitally con-

trolled drive strength that is selectable by the DS2–0 pins (see

Table 13 on Page 18). If the digitally controlled drive strength is

selected for a pin group, the DS2–0 pins determine one of eight

strength levels for that group (see Table 14 on Page 18). The

drive strength selected varies the slew rate of the driver. Drive

strength 0 (DS2–0 = 000) is the weakest and slowest slew rate.

Drive strength 7 (DS2–0 = 111) is the strongest and fastest slew

rate.

The stronger drive strengths are useful for high frequency

switching while the lower strengths may allow use of a relaxed

design methodology. The strongest drive strengths have a larger

di/dt and thus require more attention to signal integrity issues

such a ringing, reflections and coupling. Also, a larger di/dt can

increase external supply rail noise, which impacts power supply

and power distribution design.

The drive strengths for the EMU, CPA, and DPA pins are not

controllable and are fixed to the maximum level.

For drive strength calculation, see Output Drive Currents on

Page 32.

POWER SUPPLIES

The ADSP-TS101S has separate power supply connections for

internal logic (VDD), analog circuits (VDD_A), and I/O buffer

(VDD_IO) power supply. The internal (VDD) and analog (VDD_A)

supplies must meet the 1.2 V requirement. The I/O buffer

(VDD_IO) supply must meet the 3.3 V requirement.

The analog supply (VDD_A) powers the clock generator PLLs. To

produce a stable clock, systems must provide a clean power sup-

ply to power input VDD_A. Designs must pay critical attention to

bypassing the VDD_A supply.

The required power-on sequence for the DSP is to provide VDD

(and VDD_A) before VDD_IO.

FILTERING REFERENCE VOLTAGE AND CLOCKS

Figure 6 shows a possible circuit for filtering VREF, SCLK_N, and

LCLK_N. This circuit provides the reference voltage for the

switching voltage, system clock, and local clock references.

VDD_IO

R1

R2

C1

C2

VREF

SCLK_N

LCLK_N

VSS

R1: 2k⍀ SERIES RESISTOR

R2: 1.67k⍀ SERIES RESISTOR

C1: 1␮F CAPACITOR (SMD)

C2: 1nF CAPACITOR (HF SMD) PLACED CLOSE TO DSP’S PINS

Figure 6. VREF, SCLK_N, and LCLK_N Filter

DEVELOPMENT TOOLS

The ADSP-TS101S is supported with a complete set of

CROSSCORE®† software and hardware development tools,

including Analog Devices emulators and VisualDSP++®‡ devel-

opment environment. The same emulator hardware that

supports other TigerSHARC processors also fully emulates the

ADSP-TS101S.

The VisualDSP++ project management environment lets pro-

grammers develop and debug an application. This environment

includes an easy to use assembler (which is based on an alge-

braic syntax), an archiver (librarian/library builder), a linker, a

loader, a cycle-accurate instruction-level simulator, a C/C++

compiler, and a C/C++ run-time library that includes DSP and

mathematical functions. A key point for these tools is C/C++

code efficiency. The compiler has been developed for efficient

translation of C/C++ code to DSP assembly. The DSP has archi-

tectural features that improve the efficiency of compiled C/C++

code.

The VisualDSP++ debugger has a number of important fea-

tures. Data visualization is enhanced by a plotting package that

offers a significant level of flexibility. This graphical representa-

tion of user data enables the programmer to quickly determine

the performance of an algorithm. As algorithms grow in com-

plexity, this capability can have increasing significance on the

designer’s development schedule, increasing productivity. Sta-

tistical profiling enables the programmer to nonintrusively poll

the processor as it is running the program. This feature, unique

to VisualDSP++, enables the software developer to passively

gather important code execution metrics without interrupting

the real-time characteristics of the program. Essentially, the

developer can identify bottlenecks in software quickly and

efficiently. By using the profiler, the programmer can focus on

those areas in the program that impact performance and take

corrective action.

† CROSSCORE is a registered trademark of Analog Devices, Inc.

‡ VisualDSP++ is a registered trademark of Analog Devices, Inc.

Rev. C | Page 10 of 48 | May 2009

Share Link: