PLUTO 데이터 시트보기 (PDF) - Mitel Networks

부품명

상세내역

제조사

PLUTO

Dual Mode CDMA/AMPS Baseband Interface

Mitel Networks 

PLUTO

CDMA TX Section Analog Interface

The ITx and QTx outputs can be d.c. or a.c. coupled to the

external circuits and will differentially drive a minimum

resistive load of 5 kΩ and a maximum capacitive load of 20 pF.

When the CDMA transmit path is in power-down mode the

positive outputs goes high and the negative output goes low.

FM Transmit Signal Path

FM TX DAC

In FM mode, the Q-Channel DAC is used to generate an

analog FM modulation signal from the data transmitted from

the digital baseband processor. In this mode, all other CDMA

TX circuits are powered down.

FM Mode Analog Reconstruction Filters

The frequency spectrum at the output of the transmit DAC

contains unwanted frequency components. A reconstruction

filter is used to smooth the DAC output signals.

Low-pass filters are used with a cut-off frequency of

approximately 13 kHz. These filters are 3rd order Butterworth

filters.

FM TX Section Analog Interface

The FMTX output can be d.c. or a.c. coupled to the radio

circuits and will drive a minimum resistive load of 5 kΩ and a

maximum capacitive load of 20 pF.

When the FM mode is in power-down the output is in high

impedance state.

CDMA Receive Signal Path

CDMA Receive ADC

In CDMA mode two high speed 4-bit ADCs are used to

digitise the incoming signals before subsequent transmission

to the baseband digital signal processor as two parallel 4 bit

words (RXI<3:0> and RXQ<3:0>). The sample rate of

9.8304MHz is generated via an on chip synthesiser that

requires no setting up or external components. On each falling

edge of the synthesised clock (CHIPx8) a new digital sample

is output on the digital bus.

CDMA Receive Calibration Circuit

On entering into CDMA mode from power down or from FM

mode the calibration circuits are activated. These circuits

measure the differences between the receive path gain in the

pass band and in the transition band of both I and Q filters. Via

a successive approximation process they tune the receive

filters cut-off frequency and amplitude matching using the 8 bit

DACs provided for this purpose (I_FC, Q_FC and BAL). Once

both filters (I and Q) have been calibrated in this way the DAC

outputs will not change until the chip is powered down or the

calibration circuit is re-activated in some other way.

FM Receive Signal Path

In FM mode two low speed 8-bit ADCs are used to digitise

the incoming signals before subsequent transmission to the

baseband digital signal processor as two serial 8-bit words

(FMRXI & FMRXQ). The sample rate is entirely determined by

the digital baseband processor (up-to the maximum allowed)

via the FMCLK input.

In FM mode the receive filters are assumed to track the

filters used in CDMA mode i.e. there is no separate tuning

mechanism.

SYNTHESISERS

The Synthesiser block comprises the input buffers, main

dividers, phase comparator, charge pump and lock detect

circuit for a TX and RX synthesiser. The loop filter components

and the VCOs are external to the device. A common reference

divider chain is also included together with bias and control

circuitry. All blocks apart from reference divider, bias and

control logic are duplicated exactly for RX and TX

synthesisers.

The receive intermediate frequency (RX_IF) is

programmable and the transmit intermediate frequency

(TX_IF) is fixed at 130.38MHz.

AUX ADC

The auxiliary converter section contains a single 8-bit

successive approximation analog to digital converter, with

serial output. In order to maximise the flexibility of Pluto, a 4

way analog multiplexer is provided, which enables the

converter to encode any one of four selectable channels. The

converter is intended for such applications as power supply

and temperature monitoring. When not in use, the converter is

powered down, and its outputs are held low.

4

Share Link: