AM29LV008T-120FC 데이터 시트보기 (PDF) - Advanced Micro Devices

부품명

상세내역

제조사

AM29LV008T-120FC

8 Megabit (1,048,576 x 8-Bit) CMOS 3.0 Volt-only, Sectored Flash Memory

Advanced Micro Devices 

PRELIMINARY

Embedded Program or Erase Algorithm is completed,

DQ6 will stop toggling and valid data can be read on

the next successive attempts. During programming, the

Toggle Bit is valid after the rising edge of the fourth WE

pulse in the four-write-pulse sequence. During Chip

erase, the Toggle Bit is valid after the rising edge of the

sixth WE pulse in the six-write-pulse sequence. During

Sector erase, the Toggle Bit is valid after the last rising

edge of the sector erase WE pulse. The Toggle Bit is

active during the Sector Erase time-out.

Either CE or OE toggling will cause DQ6 to toggle. If

the user attempts to write to a protected sector, DATA

Polling will be activated for about 1 µs; the device will

then return to read mode, with data from the protected

sector unchanged. If the user attempts to erase a pro-

tected sector, Toggle Bit will be activated for about 50

µs; the device will then return to read mode, without

having erased the protected sector.

DQ5: Exceeded Timing Limits

DQ5 will indicate if the program or erase time has ex-

ceeded the specified limits (internal pulse count).

Under these conditions, DQ5 will produce a ‘1’ indicat-

ing that the program or erase cycle was not success-

fully completed. Write operation status and reset

command are the only operating functions under this

condition. The device will draw active power under this

condition.

The DQ5 failure condition will also appear if the user at-

tempts to write a data ‘1’ to a bit that has already been

programmed to a data ‘0’. In this case, the DQ5 failure

condition is not guaranteed to happen, since the device

was incorrectly used. Please note that programming a

data ‘0’ to a data ‘1’ should never be attempted, and

only erasure should be used for this purpose. If pro-

gramming to a data ‘1’ is attempted, the device should

be reset.

If the DQ5 failure condition is observed while in Sector

Erase mode (that is, exceeded timing limits), then DQ2

can be used to determine which sector had the prob-

lem. This is especially useful when multiple sectors

have been loaded for erase.

DQ3: Sector Erase Timer

After the completion of the initial Sector Erase com-

mand sequence, the Sector Erase time-out will begin.

DQ3 will remain low until the time-out is complete.

DATA Polling (DQ7) and Toggle Bit (DQ6) are also valid

after the first sector erase command sequence.

If DATA Polling or the Toggle Bit indicates the device

has been written with a valid Sector Erase command,

DQ3 may be used to determine if the sector erase timer

window is still open. If DQ3 is high (‘1’), the internally

controlled erase cycle has begun; attempts to write

subsequent commands to the device will be ignored

until the erase operation is completed as indicated by

the DATA Polling or Toggle Bit. If DQ3 is low (‘0’), the

device will accept additional sector erase commands.

To be certain the command has been accepted, the

software should check the status of DQ3 following each

Sector Erase command. If DQ3 was high on the sec-

ond status check, the command may not have been ac-

cepted.

It is recommended that the user guarantee the time be-

tween sector erase command writes be less than 80 µs

by disabling the processor interrupts just for the dura-

tion of the Sector Erase (30H) commands. This ap-

proach will ensure that sequential sector erase

command writes will be written to the device while the

sector erase timer window is still open.

DQ2: Toggle Bit 2

This toggle bit, along with DQ6, can be used to deter-

mine whether the device is in the Embedded Erase Al-

gorithm or in Erase Suspend.

Successive reads from the erasing sector will cause

DQ2 to toggle during the Embedded Erase Algorithm.

If the device is in the erase-suspend-read mode, suc-

cessive reads from the erase-suspended sector will

cause DQ2 to toggle. When the device is in the erase

suspend-program mode, successive reads from the

byte address of the non-erase suspended sector will in-

dicate a logic ‘1’ at the DQ2 bit. Note that a sector which

is selected for erase is not available for read in Erase

Suspend mode. Other sectors which are not selected

for Erase can be read in Erase Suspend.

DQ6 is different from DQ2 in that DQ6 toggles only

when the standard program or erase, or erase

suspend-program operation is in progress.

If the DQ5 failure condition is observed while in Sector

Erase mode (that is, exceeded timing limits), the DQ2

toggle bit can give extra information. In this case, the

normal function of DQ2 is modified. If DQ5 is at logic

‘1’, then DQ2 will toggle with consecutive reads only at

the sector address that caused the failure condition.

DQ2 will toggle at the sector address where the failure

occurred and will not toggle at other sector addresses.

Am29LV008T/Am29LV008B

17

Share Link: