HT46R01 데이터 시트보기 (PDF) - Holtek Semiconductor

부품명

상세내역

제조사

HT46R01

10-Pin MSOP A/D Type 8-Bit OTP MCU

Holtek Semiconductor 

HT46R01/HT46R02/HT46R03

Structure

The two sections of Data Memory, the Special Purpose

and General Purpose Data Memory are located at con-

secutive locations. All are implemented in RAM and are

8 bits wide but the length of each memory section is dic-

tated by the type of microcontroller chosen. The start

address of the Data Memory for all devices is the ad-

dress ²00H². Registers which are common to all

microcontrollers, such as ACC, PCL, etc., have the

same Data Memory address.

General Purpose Data Memory

All microcontroller programs require an area of

read/write memory where temporary data can be stored

and retrieved for use later. It is this area of RAM memory

that is known as General Purpose Data Memory. This

area of Data Memory is fully accessible by the user pro-

gram for both read and write operations. By using the

²SET [m].i² and ²CLR [m].i² instructions individual bits

can be set or reset under program control giving the

user a large range of flexibility for bit manipulation in the

Data Memory.

Special Purpose Data Memory

This area of Data Memory is where registers, necessary

for the correct operation of the microcontroller, are

stored. Most of the registers are both readable and

writable but some are protected and are readable only,

the details of which are located under the relevant Spe-

cial Function Register section. Note that for locations

that are unused, any read instruction to these addresses

will return the value ²00H².

Special Function Registers

To ensure successful operation of the microcontroller,

certain internal registers are implemented in the Data

Memory area. These registers ensure correct operation

of internal functions such as timers, interrupts, etc., as

well as external functions such as I/O data control and

A/D converter operation. The location of these registers

within the Data Memory begins at the address 00H. Any

unused Data Memory locations between these special

function registers and the point where the General Pur-

pose Memory begins is reserved and attempting to read

data from these locations will return a value of 00H.

Indirect Addressing Registers - IAR0, IAR1

The Indirect Addressing Registers, IAR0 and IAR1, al-

though having their locations in normal RAM register

space, do not actually physically exist as normal regis-

ters. The method of indirect addressing for RAM data

manipulation uses these Indirect Addressing Registers

and Memory Pointers, in contrast to direct memory ad-

dressing, where the actual memory address is speci-

fied. Actions on the IAR0 and IAR1 registers will result in

no actual read or write operation to these registers but

rather to the memory location specified by their corre-

sponding Memory Pointer, MP0 or MP1. Acting as a

pair, IAR0 with MP0 and IAR1 with MP1 can together ac-

cess data from the Data Memory. As the Indirect Ad-

dressing Registers are not physically implemented,

reading the Indirect Addressing Registers indirectly will

return a result of ²00H² and writing to the registers indi-

rectly will result in no operation.

00H

00H

00H

S p e c ia l P u r p o s e

D a ta M e m o ry

S p e c ia l P u r p o s e

D a ta M e m o ry

S p e c ia l P u r p o s e

D a ta M e m o ry

1FH

1FH

1FH

20H

20H

20H

G e n e ra l P u rp o s e

D a ta M e m o ry

G e n e ra l P u rp o s e

D a ta M e m o ry

G e n e ra l P u rp o s e

D a ta M e m o ry

5FH

H T46R 01

7FH

H T46R 02

BFH

H T46R 03

Data Memory Structure

Note: Most of the Data Memory bits can be directly manipulated using the ²SET [m].i² and ²CLR [m].i² with the excep-

tion of a few dedicated bits. The Data Memory can also be accessed through the memory pointer register MP.

Rev. 1.00

11

September 21, 2007

Share Link: