LC66354C, 66356C, 66358C
Pin Function Overview
Pin
I/O
Overview
Output driver type
Options
State after a reset
P00
P01
P02
P03
I/O
I/O ports P00 to P03
• Input or output in 4-bit or 1-bit units
• P00 to P03 support the halt mode control
• Pch: Pull-up MOS type
• Nch: Intermediate sink current
function
type
• Pull-up MOS or Nch
OD output
• Output level on reset
High or low
(option)
P10
P11
P12
P13
P20/SI0
P21/SO0
P22/SCK0
P23/INT0
I/O
I/O ports P10 to P13
Input or output in 4-bit or 1-bit units
• Pch: Pull-up MOS type
• Nch: Intermediate sink current
type
• Pull-up MOS or Nch
OD output
• Output level on reset
High or low
(option)
I/O ports P20 to P23
• Input or output in 4-bit or 1-bit units
• P20 is also used as the serial input SI0
pin.
• P21 is also used as the serial output
I/O
SO0 pin.
• P22 is also used as the serial clock
SCK0 pin.
• P23 is also used as the INT0 interrupt
• Pch: CMOS type
• Nch: Intermediate sink current
type
• Nch: +15-V handling when OD
option selected
CMOS or Nch OD
output
H
request pin, and also as the timer 0
event counting and pulse width
measurement input.
I/O ports P30 to P32
P30/INT1
P31/POUT0
P32/POUT1
• Input or output in 3-bit or 1-bit units
• P30 is also used as the INT1 interrupt
I/O
request.
• P31 is also used for the square wave
output from timer 0.
• P32 is also used for the square wave
• Pch: CMOS type
• Nch: Intermediate sink current
type
• Nch: +15-V handling when OD
option selected
CMOS or Nch OD
output
H
output from timer 1.
P33/HOLD
Hold mode control input
• Hold mode is set up by the HOLD
instruction when HOLD is low.
• In hold mode, the CPU is restarted by
setting HOLD to the high level.
I
• This pin can be used as input port P33
along with P30 to P32.
• When the P33/HOLD pin is at the low
level, the CPU will not be reset by a low
level on the RES pin. Therefore,
applications must not set P33/HOLD low
when power is first applied.
I/O ports P40 to P43
P40
P41
P42
P43
• Input or output in 4-bit or 1-bit units
• Pch: Pull-up MOS type
• Input or output in 8-bit units when used
I/O
in conjunction with P50 to P53.
• Can be used for output of 8-bit ROM
• Nch: Intermediate sink current
type
• Nch: +15-V handling when OD
Pull-up MOS or Nch OD
output
data when used in conjunction with P50
option selected
H
to P53.
I/O ports P50 to P53
• Input or output in 4-bit or 1-bit units
P50
P51
P52
P53/INT2
• Input or output in 8-bit units when used • Pch: Pull-up MOS type
I/O
in conjunction with P40 to P43.
• Can be used for output of 8-bit ROM
data when used in conjunction with P40
• Nch: Intermediate sink current
type
• Nch: +15-V handling when OD
Pull-up MOS or Nch OD
output
to P43.
option selected
H
• P53 is also used as the INT2 interrupt
request.
Continued on next page.
No. 5484-5/21